FujiFilm FinePix S1500 Скачать руководство пользователя страница 64

Страница: 64 / 142

FinePix S1500 Service Manual

4-6

4. Adjustments

Conﬁdential: FUJIFILM Service Center Use Only

4-5-2.

Creating a ﬁrmware SD card

To download the ﬁrmware, you must ﬁrst create a ﬁrmware SD card.
For the ﬁrmware SD card, create a separate SD card from the adjustment SD card.
If the MAIN PWB has been initialized, always download the ﬁrmware as the ﬁnal step.

<Step 1>

Download compressed Firmware (ZJ01221-100.zip) from Web server (https://denhin.fujiﬁlm.co.jp/csg_en/index.htm).

<Step 2>

Decompression the downloaded compression ﬁle.

ZJ01221-100

My Computer

3.5inch FD(A:)

(C:)

FPUPDATE.DAT

<Step 3>

Copy the decompression ﬁle "FPUPDATE.DAT", which is
stored in the folder ZJ01221-100, to the SD card.

My Computer

3.5inch FD(A:)

(C:)

FPUPDATE.DAT

Removable

disk

Содержание FinePix S1500















































































































































Результаты поиска

Содержание FinePix S1500

Отзывы:

FujiFilm FinePix S1500, Руководство по обслуживанию, Страница: 64 / 142

Результаты поиска

Содержание FinePix S1500

Отзывы: