FujiFilm FinePix S1500 Скачать руководство пользователя страница 119

Страница: 119 / 142

FinePix S1500 Service Manual

4-61

4. Adjustments

Conﬁdential: FUJIFILM Service Center Use Only

4-25. Firmware Download

[Overview]

Replace the adjustment ﬁrmware with the product ﬁrmware.
Always execute the Firmware Download after completing the adjustments.

[Note]

• Always download the latest version of the ﬁrmware.
• Do not turn the camera off until the ﬁrmware Download is completed.

<Step 1>

Insert the ﬁrmware SD card into the camera.

<Step 2>

Set the camera into the DC COUPLER CP-04N and connect the AC adapter.

<Step 3>

Set the camera's power switch to "ON" while holding down
the DISP/BACK button.

--> The ﬁrmware rewrite menu appears.

<Step 4>

Press the MENU/OK button to display the conﬁrmation
window.

<Step 5>

Press the Left button to select "OK" and then press the
MENU/OK button.

FIRMWARE UPGRADE

FIRMWARE UPGRADE OK?
VERSION : 1.xx

�

1.xx

SET

CANCEL

FIRMWARE UPGRADE

USE AC ADAPTER FOR

FIRMWARE UPGREADE
VERSION : 1.

CANCEL

YES

Содержание FinePix S1500















































































































































Результаты поиска

Содержание FinePix S1500

Отзывы:

FujiFilm FinePix S1500, Руководство по обслуживанию, Страница: 119 / 142

Результаты поиска

Содержание FinePix S1500

Отзывы: