FujiFilm ClearView CS, Руководство по обслуживанию, Страница: 1070 / 1404

CR-IR 363
Service Manual
SP-1
SP-1
011-202-07
04.25.2008 FM5281
How to Use Service
Parts List
■
RANK
●
Handling RANK characters (parts
that are handled in a special manner
during parts operation, such as
management)
Character Under Warranty Out of Warranty
R
Must be
returned.
Repairable
Q
Must be
returned.
(We use for
analysis.)
Not repairable
T
Must Not be
returned.
(Consumable
part. Not
applicable to
free-of-charge
warranty.)
Not repairable
without
R, Q, T
Must Not be
returned.
Not repairable
● Export regulation-applicable
character(Parts with the following
character are controlled by Export
regulation.)
Character Signi fi cance
＋
Parts applicable to export
regulations.
● Fault RANK characters (which provide
reference for determining the recom-
mended stock quantity)
All parts are assigned with one of characters
A through E.
Character Signi fi cance
A
Consumable parts or parts
that will be replaced at short
intervals.
B
Parts that may become faulty
accidentally and have a relatively
high failure rate.
C
Parts that have a suf fi ciently long
MTBF, but are expected to have
a relatively high failure rate.
D
Parts that have a suf fi ciently
long MTBF, but are expected to
become faulty.
E
Parts that are necessary for fault
analysis, or parts that may be
needed in case of unexpected
accidents such as man-induced
damage.
<The RANK guide>
The Fault RANK characters, Handling RANK
characters, and Export regulation-applicable
character are assigned in that order.
Thus, at least one character or up to three
characters are assigned in the RANK
column.
■
REF.NO.
REF. NO. is a part number indicated in the
Service Parts Exploded Views. For parts
having different functions, they are clearly
distinguished in the REMARKS and SERIAL
NUMBER columns.
■ PART NUMBER
PART NUMBER is a code number that is
unique to each part. An alphabetic letter at
the rightmost position of the code number
has the following meaning.
○ For hardware
The alphabet denotes the version number
of a part. If parts have different version
numbers, they are upward-compatible.
○ For software
The alphabet denotes a difference in the
speci
fi cations. Parts differing in the suf fi x
are not compatible with each other. Version
number is omitted in the list.
■
PART NAME
PART NAME represents a general name of
a part.
■ QTY.
○ QTY. denotes the quantity of parts used
in each unit.
○ A part whose quantity is suf fi xed with -S
represents a small part that is shipped in
packs of 50. (Even if such a part is ordered
in quantity of 1, a pack containing 50 pieces
of that part is supplied.)
■
REMARKS
The REMARKS column indicates a unique
name of a part or relevant information of
each part.
■ SERIAL NUMBER
The units may contain different parts
depending on their shipment control number.
SERIAL NUMBER indicates the shipment
control number to which the relevant parts
are applicable. If the SERIAL NUMBER
column is blank, the parts are applicable to
all the relevant units. The shipment control
number is represented by lower
fi ve digits
of eight-digit number indicated on the rating
indication label.
■
REFER TO
The "REFER TO" column shows reference
sections concerning the part. Clicking the
reference section in the "REFER TO" column
jumps to the top page of the reference
section where the related information is in.
■
Recommended quantities of spare
parts
It is recommended as a rough guide to hold
in stock a certain quantity of parts according
to the rank (A, B, C, D, E) assigned to the
parts, as follows. For periodically replaced
parts, hold them in stock separately. Adjust
the stock quantity of service parts depending
on the number of working units (N).
Quantity used in a single system : Q
○ N = 1
Rank A ＝ １ ＋ Ｑ × 0.3
Rank C ＝ １ ＋ Ｑ × 0.05
Rank D ＝ １ ＋ Ｑ × 0.02
○ 2 ≦ N ≦ 10
Rank A ＝ ２ ＋ Ｎ × Ｑ × 0.3
Rank C ＝ ２ ＋ Ｎ × Ｑ × 0.05
Rank D ＝ １ ＋ Ｎ × Ｑ × 0.02
○ 11 ≦ N ≦ 300
Rank A ＝ ３ ＋ Ｎ × Ｑ × 0.3
Rank C ＝ ３ ＋ Ｎ × Ｑ × 0.05
Rank D
＝ ２ ＋ Ｎ × Ｑ ×
0.02
■ Precautions to be Observed When
Returning Parts for Repair
When returning a component for repair,
pack it in the same manner as for the
supplied substitute, using the substitute
packing materials.
The use of different packing materials or
packing methods may incur damage to
packed component during transit.