Fuji Xerox DocuPrint M255 df Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 423

Fuji Xerox DocuPrint M255 df Скачать руководство пользователя страница 77

Printer Connection and Software Installation

77

Configuring Wireless Network Settings (DocuPrint
M255 z only)

You can configure wireless network settings with the

Easy Install Navi

.

IMPORTANT:

•

Be sure to obtain the SSID and security information from a system administrator in advance when you use a
communications standard other than WPS to configure wireless network settings.

•

Ensure that the Ethernet cable has been disconnected from the printer before you configure the wireless
network settings.

The wireless network specifications are described below:

You can select a method to configure wireless network settings from the following:

This section includes:

• "Using Wizard Setup to Configure Wireless Network Settings" on page 78
• "Using Advanced Setup to Configure Wireless Network Settings" on page 84
• "Setting Up a New Wireless Network Environment for Your Computer (When You Need to Set Up

Your Wireless Connectivity With Your Computer)" on page 95

Item

Specification

Connectivity

Wireless

Connectivity Standard

IEEE 802.11b/g compliant

Bandwidth

2.4 GHz

Data Transfer Rate

IEEE 802.11b mode: 11, 5.5, 2, 1 Mbps
IEEE 802.11g mode: 54, 48, 36, 24, 18, 12, 9, 6 Mbps

Security

64 (40-bit key)/ 128 (104- bit key) WEP, WPA- PSK (TKIP, AES),
WPA2-PSK (AES)(IEEE802.1x attestation function of WPA 1x non-
corresponds)

Certifications

Wi-Fi, WPA2.0 (Personal)

Wi-Fi Protected Setup (WPS)

Push Button Configuration (PBC), Personal Identification Number
(PIN), WPS2.0 supported

Wizard

Setup Through USB Connection

Advanced

Setup Through

Ethernet connection
Operator Panel
CentreWare Internet Services
WPS-PIN

*1

WPS-PBC

*2

*1 WPS-PIN (Wi-Fi

®

Protected Setup-Personal Identification Number) is a method to authenticate and

register devices required for wireless configuration, by entering PIN code in the printer and computer.
This setting, performed through access point, is available only when the access points of your wireless
router supports WPS.

*2 WPS-PBC (Wi-Fi Protected Setup-Push Button Configuration) is a method to authenticate and register

devices required for wireless configuration, by pressing the button provided on the access point via
wireless routers, and then performing WPS-PBC setting on the operator panel. This setting is available
only when the access point supports WPS.

«
...
75
76
77
78
79
...
»

Содержание DocuPrint M255 df








































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды