manualshive.com logo in svg

Fuji Xerox DocuPrint CM225FW, Руководство пользователя

Принтер Fuji Xerox DocuPrint CM225FW - это надежное и компактное устройство, отлично подходящее для дома или офиса. Пользователи могут бесплатно загрузить руководство по эксплуатации на manualshive.com. Этот мануал поможет более эффективно использовать принтер и получить отличное качество печати.

Поделиться
Скачать
background image

Maintenance

329

Ordering Supplies

The toner cartridges need to be ordered occasionally. Each toner cartridge includes installation instructions on the 
box.

Consumables

IMPORTANT: 

•

Use of consumables not recommended by Fuji Xerox can impair machine quality and performance. Use only consumables 
recommended by Fuji Xerox.

•

Average standard pages. Declared yield in accordance with ISO/IEC 19798 and ISO/IEC 24712. These values are estimates 
and vary depending on conditions such as the content being printed, paper size, paper type, the machine's operating 
environment, initializing process performed when you turn on or off the printer, and adjustments to maintain print quality.

NOTE: 

•

The printable number of pages for the starter toner cartridges shipped with the printer are approximately 1000 pages for black 
toner cartridge and 700 pages for yellow, magenta, and cyan toner cartridges.

•

Each toner cartridge includes installation instructions on the box.

When to Order Toner Cartridges

The touch panel displays a warning when the toner cartridge nears its replacement time. Verify that you have 
replacements on hand. It is important to order a toner cartridge when the messages first appear to avoid 
interruptions to your printing. The touch panel displays an error message when the toner cartridge must be replaced.
To order toner cartridges, contact the Fuji Xerox local representative office or an authorized dealer.

IMPORTANT: 

•

This printer is designed to provide the most stable performance and print quality when used with the recommended toner 
cartridges. Not using toner cartridges recommended for this machine degrades the performance and printing quality of the 
printer. You could also incur charges if the machine breaks down. To receive customer support and achieve the optimum 
performance of the printer, be sure to use recommended toner cartridges.

Recycling Supplies

•

For environmental protection and efficient use of resources, Fuji Xerox reuses returned toner cartridges and 
drums (photoreceptors) to make recycle parts, recycle materials or energy recovery.

•

Proper disposal is required for toner cartridges no longer needed. Do not open toner cartridges. Return them to 
your local Fuji Xerox representative.

Product Name

Product Code

Printable number of pages

Toner Cartridge [Black] High capacity

CT202264

Approx. 2000 pages

Toner Cartridge [Yellow] Standard capacity

CT202270

Approx. 700 pages

Toner Cartridge [Yellow] High capacity

CT202267

Approx. 1400 pages

Toner Cartridge [Magenta] Standard capacity

CT202269

Approx. 700 pages

Toner Cartridge [Magenta] High capacity

CT202266

Approx. 1400 pages

Toner Cartridge [Cyan] Standard capacity

CT202268

Approx. 700 pages

Toner Cartridge [Cyan] High capacity

CT202265

Approx. 1400 pages

Содержание DocuPrint CM225FW

























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DocuPrint CM225FW

Octave 8 Instructions For Installing preview
8
Бренд: Octave Страницы: 2
Pantum P3000 Series Maintenance Manual preview
P3000 Series
Бренд: Pantum Страницы: 94
Z Corporation ZPrinter 650 Hardware Manual preview
ZPrinter 650
Бренд: Z Corporation Страницы: 99
IBM 5218 Setup Procedures preview
5218
Бренд: IBM Страницы: 60
Konica Minolta Bizhub 222 Service Manual preview
Bizhub 222
Бренд: Konica Minolta Страницы: 846
EBS Ink-Jet Systems Hi-Res EBS-2600 Manual preview
Hi-Res EBS-2600
Бренд: EBS Ink-Jet Systems Страницы: 3
Oki ES3640eMFP Installation Instructions preview
ES3640eMFP
Бренд: Oki Страницы: 2
Xerox 4250 - WorkCentre - Copier Specifications preview
4250 - WorkCentre - Copier
Бренд: Xerox Страницы: 4
Printekmobile MLP-35 Quick Start Manual preview
MLP-35
Бренд: Printekmobile Страницы: 2
Kyocera KM-2560 Service Manual preview
KM-2560
Бренд: Kyocera Страницы: 392
Oki CX3535 Safety Information Manual preview
CX3535
Бренд: Oki Страницы: 64
Magtek ExpressCard 500 User Manual preview
ExpressCard 500
Бренд: Magtek Страницы: 49
Canon MF635Cx Series Getting Started preview
MF635Cx Series
Бренд: Canon Страницы: 236
Canon MAXIFY MB2750 Online Manual preview
MAXIFY MB2750
Бренд: Canon Страницы: 1366
Canon MAXIFY MB5150 Online Manual preview
MAXIFY MB5150
Бренд: Canon Страницы: 1356
Canon MF515 Series User Manual preview
MF515 Series
Бренд: Canon Страницы: 913
Canon MG2900 Series Manual preview
MG2900 Series
Бренд: Canon Страницы: 531
Epson WorkForce Pro WF-C8190DTWC User Manual preview
WorkForce Pro WF-C8190DTWC
Бренд: Epson Страницы: 162

Бренды по названию

Популярные бренды

Загрузить еще бренды