Fuji Xerox DocuPrint CM225FW Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 344

Fuji Xerox DocuPrint CM225FW Скачать руководство пользователя страница 30

30

Basic Operation

Turning On/Off the Printer



Turning On Your Printer

IMPORTANT:

•

Do not use extension cords or power strips.

•

The printer should not be connected to an uninterruptible power supply (UPS) system.

1

Connect the power cord to the power connector on the rear of your printer (see "Rear View" on page 26).

2

Connect the other end of the cord to the power source.

3

Turn on the printer.

NOTE:

•

When you turn on the printer for the first time, follow the on-screen instructions on the touch panel to configure the initial
settings of your printer.

See also:

•

"Setting Initial Settings on the Operator Panel" on page 32

«
...
28
29
30
31
32
...
»

Содержание DocuPrint CM225FW

























































































































































































































































































































































Отзывы:

Нет отзывов