Fuji Xerox DocuPrint CM225FW страница 243 Скачать руководство пользователя

Страница: 243 / 344

Using the Operator Panel Menus and Keypad

243

• Resolution

Purpose:
To specify the resolution level to be used for fax transmission.
Values:

NOTE:

•

Faxes scanned in the

Super Fine

mode transmit at the highest resolution supported by the receiving device.

• Original Type

Purpose:
To select the default document type.
Values:

• Lighten / Darken

Purpose:
To set the default copy density level.
Values:

• Delayed Send

Purpose:
To set a specific time for the fax transmission to start. Once the

Delayed Send

is activated, your printer stores all of

the documents to be faxed into its memory and sends them at the specified time. After faxing in the

Delayed Send

mode is complete, the data in the memory is cleared.
Values:

Standard

Suitable for documents with normal sized characters.

Fine

Suitable for documents containing small characters or thin lines or documents
printed using a dot-matrix printer.

Super Fine

Suitable for documents containing extremely fine detail. The

Super Fine

mode

is enabled only if the receiving device also supports the super fine resolution. See
the notes below.

Ultra Fine

Suitable for documents containing photographic images.

Text

Suitable for documents with text.

Photo

Suitable for documents with photos.

Lighten2

Makes the fax lighter than the original. Works well with dark print.

Lighten1
Normal

Works well with standard typed or printed documents.

Darken1

Makes the fax darker than the original. Works well with light print or faint pencil
markings.

Darken2

Hours

Specifies the fax transmission start time when sending a fax at a specified time.

Minutes

Содержание DocuPrint CM225FW
























































































































































































































































































































































Результаты поиска

Содержание DocuPrint CM225FW

Отзывы:

Похожие инструкции для DocuPrint CM225FW

Бренды по названию

Популярные бренды

Fuji Xerox DocuPrint CM225FW, Руководство пользователя

Результаты поиска

Содержание DocuPrint CM225FW

Отзывы:

Похожие инструкции для DocuPrint CM225FW

Бренды по названию

Популярные бренды