manualshive.com logo in svg

Fuji Xerox DocuPrint CM225FW, Руководство пользователя

Поделиться
Скачать
Fuji Xerox DocuPrint CM225FW Скачать руководство пользователя страница 226

226

Using the Operator Panel Menus and Keypad

Prefix Dial

Purpose:
To select whether to set a prefix dial number.
Values:

Fax Cover Page

Purpose:
To set whether to attach a cover page to faxes.
Values:

Send Header

Purpose:
To print the information of the sender on the header of the faxes.
Values:

ECM

Purpose:
To set whether to enable or disable the Error Correction Mode (ECM). To use the ECM, the remote machines must 
also support the ECM.
Values:

Modem Speed

Purpose:
To adjust the fax modem speed when a fax transmission or reception error occurs.
Values:

Off

*

Does not set a prefix dial number.

On

Sets a prefix dial number.

Prefix Dial Number

Sets prefix dial number of  up to five digits. This number dials before any auto dial 
number is started. It is useful for accessing the Private Automatic Branch 
Exchange (PABX).

Off

*

Does not attach a cover page to faxes.

On

Attaches a cover page to faxes.

Off

*

Does not print the sender's information on the header of faxes.

On

Prints the sender's information on the header of faxes.

Off

Disables the ECM.

On

*

Enables the ECM.

2.4 Kbps
4.8 Kbps
9.6 Kbps
14.4 Kbps
33.6 Kbps

*

Содержание DocuPrint CM225FW

























































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды