Fuji Xerox DocuPrint CM225FW Скачать руководство пользователя страница 218 | Manualshive

Страница: 218 / 344

Fuji Xerox DocuPrint CM225FW Скачать руководство пользователя страница 218

218

Using the Operator Panel Menus and Keypad

IPsec

NOTE:

•

IPsec feature is available only when IPsec is enabled on the CentreWare Internet Services.

Purpose:
Disables IPsec.
Value:

Reset Wireless

NOTE:

•

Reset Wireless feature is available only when the printer is connected using the wireless network.

Purpose:
To reset the wireless connection settings. After executing this function, all information about the access point is
cleared.
Value:

Connection Speed

NOTE:

•

Connection Speed feature is available only when the printer is connected using the wired network.

Purpose:
To specify the communication speed and the duplex settings of Ethernet. The change becomes effective after the
printer is turned off and then on again.
Values:

• Wi-Fi Direct

Purpose:
To configure the Wi-Fi Direct

®

settings.

Values:

Disable

Disables IPsec.

Reset

Resets the wireless connection settings.

Auto

*

Detects the Ethernet settings automatically.

10Base-T Half

Uses 10Base-T Half-duplex.

10Base-T Full

Uses 10Base-T Full-duplex.

100Base-T Half

Uses 100Base-T Half-duplex.

100Base-T Full

Uses 100Base-TX Full-duplex.

Wi-Fi
Direct

Disable

*

Disables the Wi-Fi Direct connection.

Enable

Enables the Wi-Fi Direct connection.

Connection
Status

No Entry

Indicates that no device is available.

Displays the
connected device
name and current
role.

Disconnect
now

Disconnect the connected device when using Wi-Fi Direct.

Disconnect
and Reset
Passphrase

Disconnect the connected device and reset passphrase when
using Wi-Fi Direct.

Device Name

Displays the printer name.

SSID

Specify a name to identify the wireless network.

Passphrase

Print
Passphrase

Prints the passphrase. Confirm it when you enter the passphrase to your mobile
device.

Reset
Passphrase

Resets the passphrase.

«
...
216
217
218
219
220
...
»

Содержание DocuPrint CM225FW

























































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды