Fuji Xerox DocuPrint CM225FW Скачать руководство пользователя страница 18

Страница: 18 / 344

Specifications

Output Tray Capacity

Approximately 100 sheets (face down

)

IMPORTANT:

•

When using Fuji Xerox P paper (64 gsm)

Power Supply

AC 110 – 127 V ± 10%; 7 A; both 50/60 Hz ± 3 Hz
AC 220 – 240 V ± 10%; 5 A; both 50/60 Hz ± 3 Hz

IMPORTANT:

•

Power outlets that provide the above power level are recommended.

Power Consumption

Maximum power consumption: 820 W or less
Low power mode: 25 W or less
Sleep mode: 3 W or less
Standby mode: 42 W or less

Dimensions

410 (W)



439 (D)



388 (H) mm

Weight

17 kg

IMPORTANT:

•

The weight of paper is not included.

•

The weight of the toner cartridges is included.

Space Requirement

921 (W)



1310 (D)

IMPORTANT:

•

When the standard 150 sheet tray is pulled out and the rear cover is open.

Содержание DocuPrint CM225FW
























































































































































































































































































































































Результаты поиска

Содержание DocuPrint CM225FW

Отзывы:

Бренды по названию

Популярные бренды

Fuji Xerox DocuPrint CM225FW, Руководство пользователя

Результаты поиска

Содержание DocuPrint CM225FW

Отзывы:

Бренды по названию

Популярные бренды