Fuji Xerox DocuPrint CM225FW Скачать руководство пользователя

Страница: 178 / 344

178

Faxing



Lighten / Darken

To adjust the contrast to make the fax lighter or darker than the original:

Press the

(

Services Home

) button.

Select

Fax

Select

Lighten

Darken

Select the desired setting, and then select

NOTE:

•

The value marked by an asterisk (*) is the factory default setting.



Resolution

To specify the resolution level to be used for fax transmission:

Press the

(

Services Home

) button.

Select

Fax

Select

Resolution

Select the desired setting, and then select

NOTE:

•

The value marked by an asterisk (*) is the factory default setting.

NOTE:

•

Faxes scanned in the

Super Fine

mode transmit at the highest resolution supported by the receiving device.

Lighten2

Makes the fax lighter than the original. Works well with dark print.

Lighten1
Normal

Works well with normal typed or printed documents.

Darken1

Makes the fax darker than the original. Works well with light print or faint pencil
markings.

Darken2

Standard

Suitable for documents with normal sized characters.

Fine

Suitable for documents containing small characters or thin lines or documents
printed using a dot-matrix printer.

Super Fine

Suitable for documents containing extremely fine detail. The

Super Fine

mode

is enabled only if the remote machine also supports the super fine resolution.

Ultra Fine

Suitable for documents containing photographic images.

Содержание DocuPrint CM225FW
























































































































































































































































































































































Результаты поиска

Содержание DocuPrint CM225FW

Отзывы:

Похожие инструкции для DocuPrint CM225FW

Бренды по названию

Популярные бренды

Fuji Xerox DocuPrint CM225FW, Руководство пользователя

Результаты поиска

Содержание DocuPrint CM225FW

Отзывы:

Похожие инструкции для DocuPrint CM225FW

Бренды по названию

Популярные бренды