Fuji Xerox DocuPrint C3055 DX Скачать руководство пользователя страница 115 | Manualshive

Страница: 115 / 238

Fuji Xerox DocuPrint C3055 DX Скачать руководство пользователя страница 115

5.2 Setting the Common Menus

115

[Sleep Mode]

Note

• This item does not appear on the models available in China. The Sleep mode cannot be disabled on

those models.

[Sleep Mode Timer]

[Time-out]

System Settings

Sleep Mode

Setting Item

Description

Sleep Mode

Consumes less electricity than the Low Power mode. Set whether to enable
this feature.
• [Enable] (default)
• [Disable]

Refer to

• "2.4 Setting/Exiting the Power Saver Modes" (P. 40)
• "Setting Example: Changing the Power Saver Mode Setting" (P. 92)

System Settings
Sleep Mode Timer

Setting Item

Description

Sleep Mode Timer

Sets the amount of time before the printer enters the Sleep mode from the Low
Power mode. Specify the value in 1 minute increments. (See *2 on P. 130.)
• [1 Min] to [120 Min] (default: [5 Min])

Note

• This setting is valid only if [Sleep Mode] is set to [Enable].

Refer to

• "2.4 Setting/Exiting the Power Saver Modes" (P. 40)
• "Setting Example: Changing the Power Saver Mode Setting" (P. 92)

System Settings

Time-out

Setting Item

Description

Time-out

Sets the amount of time the printer waits for a print job. If a time-out occurs dur-
ing data reception, the printer stops the reception and starts printing the
received data.
Specify the time-out value in 1 minute increments.
• [Off]

Disables the time-out function.

• [5 Sec] to [300 Sec] (default: [30 Sec])

«
...
113
114
115
116
117
...
»

Содержание DocuPrint C3055 DX















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды