Fuji Xerox DocuPrint C2120 Скачать руководство пользователя

Страница: 25 / 206

1.2 Setting the Network Environment

To Set the Subnet Mask/Gateway Address

17. Press the < > button until [Subnet Mask]

is displayed.

18. Press the < > or <Eject/Set> button to

accept the selection.
The current subnet mask is displayed.

19. Enter the subnet mask in the same way you

entered the IP address, and press the
<Eject/Set> button to confirm your entry.

20. Press the < > button to return to [Subnet

Mask].

21. Press the < > button to display [Gateway

Address].

22. Press the < > or <Eject/Set> button to

accept the selection.
The current gateway address is displayed.

23. Enter the gateway address in the same way

you entered the IP address, and press the
<Eject/Set> button to confirm your entry.

24. Setup is now complete.

Reboot the printer by turning off and on the
printer.

25. Print the [Printer Settings] list to verify your

settings.

IPv4
Subnet Mask

Subnet Mask
000.000.000.000*

Subnet Mask

255.255.255.000*

IPv4
Subnet Mask

IPv4
Gateway Address

Gateway Address
000.000.000.000*

Gateway Address
192.168.001.254*

Содержание DocuPrint C2120














































































































































































































Результаты поиска

Содержание DocuPrint C2120

Отзывы:

Похожие инструкции для DocuPrint C2120

Бренды по названию

Популярные бренды

Fuji Xerox DocuPrint C2120, Руководство пользователя

Результаты поиска

Содержание DocuPrint C2120

Отзывы:

Похожие инструкции для DocuPrint C2120

Бренды по названию

Популярные бренды