Fuji Xerox DocuPrint C2120 Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 206

background image

6.5 Paper Feeding Problems

117

6.5

Paper Feeding Problems

Symptom

Cause/Remedy

Paper does not feed properly.

Paper jams occur.

Multiple sheets are fed at once.

Paper is fed skewed.

Output is wrinkled.

Is the paper loaded correctly?
Reload the paper correctly. Before loading labels or envelopes, fan them to make sure
that they are separated.
If using coated paper, load one sheet at a time.

Isn't the paper damp?
Load new paper.

Is the paper recommended for the printer?
Load the recommended paper. Paper may still wrinkle depending on its type or
condition.

Refer to

• "Supported Paper" (P. 71)

Is the paper tray pushed in completely?
Push the tray firmly into the printer.

Is the printer installed on a level surface?
Install the printer on a level and sturdy surface.

Are the paper guides adjusted properly?
Adjust the paper guides.

Refer to

• "4.2 Loading Paper" (P. 76)

Did you add more paper on top of other paper in a tray?
Remove the paper, fan and align the paper on a flat surface, and reload the paper in the
tray. Only add paper in a tray when the tray is empty.

The feed rollers may be worn or have reached the end of their duty cycle.
Clean the feed rollers.
If the problem persists, the Feed Roller Unit must be replaced. Contact our Customer
Support Center or your dealer.

Refer to

• "7.14 Moving the Printer" (P. 175)

When loading paper in the Manual Feeder, insert the paper straight into the Manual
Feeder slot.
If the paper is inserted diagonally, remove the paper and insert it again. Insert only one
sheet of paper at a time in the Manual Feeder.

The printer does not feed
paper from the Manual Feeder.

Is the Paper Tray set to [Auto Paper Select] in the [Paper/Output] tab?
If so, deselect [Auto Paper Select] when using the Manual Feeder.

Refer to

• Online help for the print driver

The printer does not feed
paper from the paper tray.

If paper is loaded in the Manual Feeder, the paper is fed from the Manual Feeder even
if you specified the paper tray on the print driver.
To feed the paper from the paper tray, remove the paper from the Manual Feeder.

Print media misfeeds or
multiple feeds occur.

Turn the print media over or around and try printing again to see if feeding improves.

«
...
115
116
117
118
119
...
»

Содержание DocuPrint C2120















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DocuPrint C2120

Бренд: Oce Страницы: 255

Бренд: Felix Storch Страницы: 41

RS/6000 44P Series 270

Бренд: IBM Страницы: 216

Бренд: QMS Страницы: 144

Бренд: Chamjin I&C Страницы: 21

Бренд: Oki Страницы: 32

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 96

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 78

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 32

Бренд: Oki Страницы: 52

Бренд: Oki Страницы: 49

Бренд: Oki Страницы: 48

Бренд: Oki Страницы: 161

Бренд: Oki Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды