Fuji Xerox DocuPrint C1110 B страница 87 Скачать руководство пользователя | Manualshive

Страница: 87 / 209

background image

5.2 Description of Menu Items

87

TCP/IP

Specifies the settings to use the TCP/IP protocol.

IP Mode

Sets the IP (Internet Protocol) version to be used for the communication between the
printer and clients.
Installing the network expansion card (optional) to the printer allows the IPv6
communication.
• [Dual Stack] (default)

Enables both IPv4 and IPv6 communications.

• [IPv4]

Enables the IPv4 communication.

• [IPv6]

Enables the IPv6 communication.

Note

• [IP Mode] appears only when the network expansion card (optional) is installed.
• To use the IPv6 feature, refer to "Using the Printer in an IPv6 Environment" (P. 25) or

the online help for CentreWare Internet Services.

IPv4

Sets the IP address to be used for the IPv4 communication.
[Get IP Address]
Sets whether to automatically or manually retrieve the IP address.
• [DHCP/Autonet] (default)

Automatically sets the IP address.

• [BOOTP]

Uses BOOTP to set the IP address automatically.

• [RARP]

Uses RARP to set the IP address automatically.

• [DHCP]

Uses DHCP to set the IP address automatically.

• [Panel]

Sets the IP address manually by entering it on the control panel.

[IP Address]/[Subnet Mask]/[Gateway Address]
Allows you to verify or manually enter the IP address.
Enter the IP address in the format of:
xxx.xxx.xxx.xxx
For IP or gateway addresses, xxx can be any number between 0 and 255. However, the
first xxx cannot be 127 or a number between 224 and 255.
For subnet masks, each xxx must be one of the following numbers:
0, 128, 192, 224, 240, 248, 252, 254, and 255.

Important

• To set addresses manually, set [Get IP Address] to [Panel].
• IP addresses are managed in the entire network. An incorrect IP address may affect

the whole network. For the addresses you need to set manually, consult your network
administrator.

IPsec

Disables the IPsec feature.
If the network expansion card (optional) is installed, enabling the IPsec feature allows
data encryption between the printer and clients over a network.

Note

• [IPsec] appears only when the network expansion card (optional) is installed.
• To enable the IPsec feature, configure the settings on CentreWare Internet Services.

For more information, refer to the online help for CentreWare Internet Services.

• [IPsec] does not appear on the model available in China.

Item

Description

«
...
85
86
87
88
89
...
»

Содержание DocuPrint C1110 B


















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DocuPrint C1110 B

Panafax UF-7000

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 68

Бренд: Panasonic Страницы: 120

Бренд: Panasonic Страницы: 100

KX-MB781 - B/W Laser - All-in-One

Бренд: Panasonic Страницы: 96

Бренд: Panasonic Страницы: 130

Бренд: Oki Страницы: 210

Бренд: Panasonic Страницы: 77

Бренд: Panasonic Страницы: 402

Бренд: Panasonic Страницы: 54

Workio DP-8016P

Бренд: Panasonic Страницы: 88

Бренд: Panasonic Страницы: 60

Power Defense PD3

Бренд: Eaton Страницы: 4

Бренд: TallyGenicom Страницы: 145

T2265 SprintPro

Бренд: Tally Страницы: 217

Бренд: TallyGenicom Страницы: 12

Бренд: Xerox Страницы: 3

Бренд: Xerox Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды