Fuji Xerox DocuPrint C1110 B страница 11 Скачать руководство пользователя | Manualshive

Страница: 11 / 209

background image

Safety Notes

11

Safety Notes

Before using this product, read "Safety Notes" carefully for safety use.
This product and recommended supplies have been tested and found to comply with strict safety
requirements including safety agency approvals and compliance with environmental standards. Follow the
following instructions for safety use.

Any unauthorized alteration including an addition of new functions or connection

to external devices may not be covered by the product warranty. Contact your
local Fuji Xerox representative for more information.

Follow all warning instructions marked on this product. The warning marks stand for the followings:

Electrical Safety

This product shall be operated by the
power source as indicated on the product's
data plate. Consult your local power
company to check if your power source
meets the requirements.

Connect this product to

a protective earth circuit.

This product is supplied with a plug that has
a protective earth pin. The plug fits only into
an earthed electrical outlet. This is a safety
feature. If the plug doesn't fit to the outlet,
contact an electrician to replace the outlet
to avoid risk of electric shock. Never use an

Used for item that if not followed strictly, can lead death or severe or
fatal injuries and the possibility to do it is comparatively high.

Used for items that if not followed strictly, can lead to severe or fatal
injuries.

Used for items that if not followed strictly, can cause injuries to user or
damages to machine.

: A symbol for items to pay attention to when handling machine.

Follow instructions carefully to use machine safely.

: A symbol for prohibited items. Follow instructions carefully to avoid

any dangerous acts.

: A symbol for items that must be performed. Follow instructions

carefully to carry out these essential tasks.

Caution

Flammable Explodable

Electric

shock

Heated
surface

Moving

object

Pinched

fingers

Prohibited

No fire

Do not

touch

Do not use

in bathroom

Do not

tear down

Keep away

from wet

Never touch

with wet hand

Instructions

Unplug

Ground/

Earth

«
...
9
10
11
12
13
...
»

Содержание DocuPrint C1110 B


















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DocuPrint C1110 B

Бренд: Canon Страницы: 11

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 12

PIXMA Pro9000 Mark II Series

Бренд: Canon Страницы: 4

Бренд: SPRT Страницы: 28

Бренд: MakerBot Страницы: 48

Бренд: Oki Страницы: 32

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 96

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 78

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 32

Бренд: Oki Страницы: 52

Бренд: Oki Страницы: 49

Бренд: Oki Страницы: 48

Бренд: Oki Страницы: 161

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды