Fuji Xerox DocuCentre S1810 страница 194 Скачать руководство пользователя

Страница: 194 / 202

12 Appendix

194

pe
nd
ix

Notes and Restrictions

This section describes the notes and restrictions to observe when using the machine.

Notes and Restrictions on the Use of the Machine

Notes on Switching Off the Power

After the power is switched off, the machine performs internal power off processes for

a while. After turning the power off, turning it on again before the screen display has

disappeared will not start the machine right away. Before turning the power on, check

that the operation screen display has disappeared.

Installing and Moving the Machine

Contact our Customer Support Center or a Customer Engineer before moving the
machine.

Do not subject the machine to shocks while it is in operation.

Take care not to get fingers caught when closing the document cover.

Do not place objects near fan intakes on the machine's outer casing.

Character Codes

In data transmission from a computer, if characters that the machine does not support

are included in the file names, these characters may not be displayed correctly. Only

ASCII characters can be used.

Hard Disk

You cannot install a hard disk into this product.

Printing Results

Depending on the type of media used, rubber roller marks may be left behind along
the scanning direction or toner wax components adhere to the paper during 2 Sided
printing or when the output destination is changed during continuous printing.

Droplets of water may adhere to the printing paper immediately after the power is
turned on to the machine.

Depending on the type of media used, pinch roller marks and minute scratches may
form in the scanning direction.

During two-side printing with coated paper, indentations may appear on the back
side of the paper.

Line unevenness may occur along the scanning direction in high-volume printing in
low-humidity environments.

Colors may appear muted on the underside of high-density images in printing in low-
temperature, low-humidity environments.

Small white spots may appear within images on the back side of the paper in printing
in low-humidity environments.

Document Feeder

The machine does not detect a document placed in the document feeder during Sleep

mode.

Содержание DocuCentre S1810










































































































































































































Результаты поиска

Содержание DocuCentre S1810

Отзывы:

Похожие инструкции для DocuCentre S1810

Бренды по названию

Популярные бренды

Fuji Xerox DocuCentre S1810, Руководство пользователя

Результаты поиска

Содержание DocuCentre S1810

Отзывы:

Похожие инструкции для DocuCentre S1810

Бренды по названию

Популярные бренды