Fuji Xerox ApeosPort-V 6080 Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 745

Fuji Xerox ApeosPort-V 6080 Скачать руководство пользователя страница 77

Replacing Consumables

77

M

a

int

e

na
nc
e

3

6

With holding the tabs, return new cartridge to
the original position, and then gently push the
cartridge in until it clicks into place

7

Repeat steps 3 to 6 to replace the other cartridge.

8

Return the unit to the original position.

9

Close the finisher front door.

Note

•

If the finisher front door is not completely closed, a message will appear and the machine will
remain paused.

Emptying the Hole Punch Waste Container (for C3 Finisher, C3 Finisher with
Booklet Maker, D2-Staple-Finisher or D2-Staple-Finisher with Booklet Maker)

When the C3 Finisher (optional), the C3 Finisher with Booklet Maker (optional), the D2-
Staple-Finisher (optional) or the D2-Staple-Finisher with Booklet Maker (optional) is
installed and the hole punch waste container becomes full, a message appears on the touch
screen. When the message appears, empty the hole punch waste container as instructed.

Make sure to discard all paper chads when emptying the hole punch waste container. Not
doing so will cause the container to fill up before the message telling you to empty the
container appears again, and this can cause machine malfunction.

Important •

Empty the hole punch waste container when the machine is on. If you empty the container while the
machine is off, the machine does not recognize that the container has been emptied.

•

Empty the hole punch waste container after the message appears. Otherwise, the machine cannot
recognize the correct remaining amount of the punch scraps.

•

When the machine is in Power Saver mode, exit Power Saver mode by pressing the <Power Saver>
button and the <Machine Status> button on the control panel before you empty the punch waste
container.

•

Before emptying the punch waste container, press the <Machine Status> button and check the
current status for the punch waste container even when the control panel is lit.

«
...
75
76
77
78
79
...
»

Содержание ApeosPort-V 6080










































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды