Fuji Xerox ApeosPort-V 4070 Скачать руководство пользователя страница 181 | Manualshive

Страница: 181 / 719

background image

Connectivity & Network Setup

181

Tools

5

ThinPrint

Port Status

You can use the machine for print in the ThinPrint

®

.print environment. The machine

decompresses and prints the compressed print data sent from the print server.

Select [Enabled] when you use ThinPrint.

Port Number

Enter a port number for ThinPrint from 1 to 65535.

The default value is 4000.

Important •

Do not use any number s assigned to the other ports.

Note

•

ThinPrint is available when the communication protocol uses IPv4.

•

The maximum of three connections are possible at a time.

Protocol Settings

Set the parameters required for communications. In [Protocol Settings], you can set the
following items.

Also on [Ping Connection Test], you can check whether or not the machine can be properly
connected to a network with the configured condition.

Ethernet Settings

Configure the Ethernet settings.

Ethernet1 - Network Name, Ethernet 2 - Network Name

When two Ethernet interfaces are used, specify the names respectively.

Note

•

This item is displayed only when Secondary Ethernet (optional) is installed on the machine.

Ethernet - Rated Speed / Ethernet 1 - Rated Speed, Ethernet 2 - Rated Speed

Set the communication speed for the Ethernet interface.

Note

•

The title of this setting item differs depending on the Ethernet interface configuration: When single
Ethernet interface is used, [Ethernet - Rated Speed] is displayed. When two Ethernet interfaces are
used, [Ethernet 1 - Rated Speed] and [Ethernet 2 - Rated Speed] are displayed.

z

Auto

Select this to detect the Ethernet transmission rate automatically.

z

100 Mbps Full-Duplex

Select this to set 100BASE-TX (Full Duplex) as the default value.

z

100 Mbps Half-Duplex

Select this to set 100BASE-TX (Half Duplex) as the default value.

z

10 Mbps Full-Duplex

Select this to set 10BASE-T (Full Duplex) as the default value.

z

10 Mbps Half-Duplex

Select this to set 10BASE-T (Half Duplex) as the default value.

z

1000 Mbps

Select this to set 1000BASE-T as the default value.

Note

•

1000BASE-T is not available for some models. An optional component is required.

«
...
179
180
181
182
183
...
»

Содержание ApeosPort-V 4070
















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ApeosPort-V 4070

Бренд: Dascom Страницы: 12

Бренд: Dascom Страницы: 19

Бренд: Dascom Страницы: 5

Бренд: Panduit Страницы: 74

Бренд: Tally Страницы: 2

Бренд: Tally Dascom Страницы: 57

Бренд: Fenix Страницы: 65

EasyCoder 501 SA

Бренд: UBI Страницы: 214

Бренд: UBI Страницы: 64

Бренд: Kyocera Mita Страницы: 209

Бренд: Xerox Страницы: 2

Бренд: Printronix Страницы: 206

ColorPainter M-64S

Бренд: Oki Страницы: 84

WorkCentre 7970

Бренд: Xerox Страницы: 268

Бренд: IBM Страницы: 4

ThermalTronix TT-1025EX-MIL

Бренд: Intellisystem Страницы: 11

DURA PRINTER SI600

Бренд: Nitto Denko Страницы: 174

Бренд: Code Soft Страницы: 101

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды