Fuji Electric Frenic lift Скачать руководство пользователя страница 234

Страница: 234 / 254

3.4 Programming Mode

hap.
3

-A1

-LM
2"

3.4.3 Function Codes

PRG > 2

Function code data settings and changes, including copying and initializing data, can be made via

programming mode menu number 2, "Function Code".

3.4.3.1 Setting up function code data: “Data Set”

PRG > 2 > 1

This section explains how to set function code data.
The examples below show how to change “F03: Rated speed” from 1450 r/min to 1800 r/min.

Figure 3.8 Screen transition example for setting function code



Double-key operation

Some important function codes (for example, H03: Initialization) require double-key operation to

prevent misoperation.
In order to change their data, press key and key to increase, or key and key to decrease.



Changing function code data while running

Data for some function codes can be changed when the inverter is running; others cannot. Furthermore,

for some function codes, changing the data will cause those values to be reflected immediately without

storing in inverter operation; for other function codes, they will not be reflected.



For details on function codes, refer to the "2.2 Function Code Table" in Chapter 2.

REM

Data Set

PRG

PRG>2>1

S.Spd

1450

r/min

Acc/dec time1

Acc/dec time2

Torque boost

Base speed

Rated voltage

F:Fundamental

REM

Storing...

PRG>2>1>

S.Spd

1450

r/min

Rated speed

1800

F03

r/min

.00

REM

Data Set

PRG

Ope

PRG>2>1

S.Spd

1450

r/min

Data protection

Speed command

Rated speed

Base speed

Rated voltage

F:Fundamental

REM

Data Set

PRG

Ope

PRG>2>1

S.Spd

1450

r/min

F:Fundamental

E:Extension

C:Control

P:Motor Param

H:High Perform

H1:High Perform

REM

Function Code

PRG>2

S.Spd

1450

r/min

Data Set

Data Check

Changed Data

Data Copy

Initialize

REM

PRG

S.Spd

1450

r/min

Quick Setup

Start-up

Function Code

INV Info

Alarm Info

User Config

PRG Menu

PRG RESET

REM

PRG

Operat.Mode

PRG>2>1>

S.Spd

1450

r/min

Rated speed

30.00~6000.00

1450

F03

Def.

Store

r/min

.00

r/min
r/min

1450.00

Select a target function code

group by using / keys.

Then press key.

Select a target function code

by using / keys.

Then press key.

Select a target menu item by using / keys.

Then press key.

Adjust data value by using

/ / / keys.

Then press key to store

data into memory.

Inverter memorizes changed

data, and moves next screen

automatically.

Inverter shows function code

selection screen with pointing

next function code by cursor.

“

Changed

”

marker

shows the data changed

from factory default value.

3-13

Содержание Frenic lift































































































































































































































































Результаты поиска

Содержание Frenic lift

Отзывы:

Похожие инструкции для Frenic lift

Бренды по названию

Популярные бренды

Fuji Electric Frenic lift, Справочное руководство

Результаты поиска

Содержание Frenic lift

Отзывы:

Похожие инструкции для Frenic lift

Бренды по названию

Популярные бренды