Fuji Electric Frenic lift Скачать руководство пользователя страница 225

Страница: 225 / 254

Table 3.3 Icons on the LCD Monitor

Status icons that show the running status, run command sources and various icons

Running status

(rotation direction)

Running forward
Running reverse

Run command source

External terminals
Communications link
Keypad in local mode

Password protection state

Locked with password 1 (Function code data change is prohibited.)
Lock being released (Password being canceled temporally)

Travel direction

(Appears during Programming

mode and Alarm mode.)

Traveling upward
Traveling downward

Running status

No run command entered or inverter stopped
Run command entered or during inverter output

Travel direction indicator

Travel direction

(Appears during Running mode.)

Traveling upward
Traveling downward

Table 3.4 Status messages on the LCD Monitor

Status messages

Appearance condition

Low Supply Volt

Run command is turned ON at low supply voltage.

EN Off

Run command is turned ON when [EN1] and/or [EN2] are being released.

BX Active

Run command is turned ON when

command is being turned ON.

AutoReset ALM

Inverter is trying / waiting to reset the alarm automatically.

Pre-Alarm

Inverter is detecting pre-alarm by overheat.

Standby

Inverter is in standby mode by means of

STBY

command.

Unlocking SG

Inverter is trying to unlock safety gear by means of

ULSG

command.

Rescue by BRKS

Inverter is releasing brakes for emergency rescue operation by means of

RBRK

command.

Battery Op.

Inverter is operating as battery mode by means of

BATRY

command.

DC-Cap. Measure

Inverter is measuring its main capacitor lifetime before turning power OFF.

L.Factor Measure

Inverter is measuring load factor of the applying system.

LCD has temperature characteristics. The low temperature slows down the LCD response;

the high temperature makes the screen contrast high so that contrast adjustment may be

needed.

3-4

Содержание Frenic lift































































































































































































































































Результаты поиска

Содержание Frenic lift

Отзывы:

Похожие инструкции для Frenic lift

Бренды по названию

Популярные бренды

Fuji Electric Frenic lift, Справочное руководство

Результаты поиска

Содержание Frenic lift

Отзывы:

Похожие инструкции для Frenic lift

Бренды по названию

Популярные бренды