Fuji Electric Frenic lift Скачать руководство пользователя страница 215

Страница: 215 / 254

K codes (Keypad functions)

2.3.9

K01

LCD monitor (Language selection)

K01 specifies the language to display on the multi-function keypad as follows:

Data for K01

Language

Data for K01

Language

Japanese

Greek

English

Turkish

German

Polish

French

Czech

Spanish

Swedish

Italian

Portuguese

Chinese

Dutch

Russian

100

User-customizable

If the langue for touch panel which connect with inverter is not belong to above range,

English will be indicated.

K02

LCD monitor (Backlight off time)

K02 specifies the backlight OFF time of the LCD on the keypad.
When no keypad operation is performed during the time specified by K02, the backlight goes OFF.
-Data setting range: 1 to 30 (min.), OFF

Data for K02

Function

OFF

Always turn the backlight OFF

1 to 30 (min.)

Turn the backlight OFF automatically after no keypad operation

is performed during the backlight OFF time.



The backlight OFF time can be configured easily in Programming mode as follows.

PRG > 1(Start-up) > 3(Disp Setting) > 9(Lighting time)

K03

K04

LCD monitor (Backlight brightness control)

(Contrast control)

These function codes control the backlight brightness and contrast.
-Data setting range: 0 to 10



Backlight brightness control (K03)

Data for K03

0, 1, 2,

•

8, 9, 10

Dark Light



Contrast control (K04)

Data for K04

0, 1, 2,

•

8, 9, 10

Dark Light

2-202

Содержание Frenic lift































































































































































































































































Результаты поиска

Содержание Frenic lift

Отзывы:

Похожие инструкции для Frenic lift

Бренды по названию

Популярные бренды

Fuji Electric Frenic lift, Справочное руководство

Результаты поиска

Содержание Frenic lift

Отзывы:

Похожие инструкции для Frenic lift

Бренды по названию

Популярные бренды