FUJI CONTROLS IN-100 Скачать руководство пользователя страница 49

Страница: 49 / 61

Hold Mode

What is "Hold Mode"?

This function allows you to select how to display a value from the beginning to the end of

load measurement.

When By menu is set by Hold mode selection, the mode of load value display is switched

over between the peak hold mode and the sample hold mode.

PEAK

is the peak hold mode, while

SAMPLE

the sample hold mode.

The peak hold mode holds and judges the maximum value of load from the beginning of

load measurement to end signal.

The sample hold mode holds and judges the instantaneous load when end signal.

How to set

1. Press MENU key.

2. Use



⋀



⋁

key to select

Hold Function Setting

3. Press SET key.

4. Use



⋀



⋁

key to select

Hold Mode

5. Press SET key.

6. Use



⋀



⋁

key to select PEAK or SAMPLE. (default: PEAK)

7. Press SET key and confirm the cursor has turned green.

8. Press SET key again to complete this operation.

Содержание IN-100






























































Результаты поиска

Содержание IN-100

Отзывы:

Похожие инструкции для IN-100

Бренды по названию

Популярные бренды

FUJI CONTROLS IN-100, Инструкция по эксплуатации

Результаты поиска

Содержание IN-100

Отзывы:

Похожие инструкции для IN-100

Бренды по названию

Популярные бренды