background image

Rev. 16/02/2021 
 

Definitions 

¹ Water Filter Systems are defined as systems designed for drinking water under our Water filter Systems, Reverse Osmosis Systems & Ultraviolet 
Sanitation Categories – Excluding Cartridges and Shower Filters.  
² Other products not manufactured or assembled by FSA are covered under the applicable manufacturer’s warranty. 
³ FSA specifies recommended or required filter maintenance – see product information for further details. If a maintenance schedule is not 
specified, filter maintenance is required at least once per 12 month period. 
* Unsuitable environmental conditions include but are not limited to; Excessive hot or cold, Weather extremes. 

Extended Warranty 

Filter Systems Australia RO Portable Systems are eligible for an extended 4-year warranty (commencing no later than 
12 months from sale date), to provide a total warranty of 5 years. This extended warranty is subject to terms and 
conditions outlined below. This extended warranty covers the below parts of the system. 

 

GT8-31  

Reverse Osmosis Housing 

 

GT8-0S  

Twin O-ring White Housing (GT1-39 Models Only) 

 

GT8-38S 

Twin O-ring Clear Housing (GT1-39 Models Only) 

The following components are also eligible for an extended 12-month warranty (commencing no later than 12 months 
from sale date), to provide a total warranty of 2 years. This extended warranty covers the below parts of the system. 

 

GT25-3S1/4 

Diverter Valve 

 

GT10-31-DM 

DMfit ¾” Outdoor Tap Adaptor 

 

GT15-33S 

¾” Laundry Block Adaptor 

 

GT14-2LS 

¼” Inline Brass Tap 

 

GT13-   

200/300/400 cc Flow Restrictor 

 

GT13-73LS 

600cc Manual Flush Valve (GT1-39 Models Only) 

Extended Warranty Qualification 

Extended Warranty is valid only if the following conditions are met: 

 

All conditions under “Qualification for Warranty” are met. 

 

The System was installed in accordance with the manufacturer’s instructions 

 

The system was maintained in accordance with FSA recommendations in Maintenance – Section II & III. 
Replacement Cartridges. 

o

 

Cartridges must be purchased through FSA or participating supplier/reseller of FSA products 

o

 

Proof of purchase for replacement filters required. 

 

Содержание GT1-70DI











Отзывы: