FrSky D8R-XP, Инструкция по эксплуатации

Страница: 1 / 3

www.frsky-rc.com
18/05/12
1
Instruction Instruction Instruction Instruction Manual Manual Manual Manual for for for for FrSky FrSky FrSky FrSky D8R- D8R- D8R- D8R-XP XP XP XP
1. 1. 1. 1. Introduction Introduction Introduction Introduction
1.1 1.1 1.1 1.1 Compatibility Compatibility Compatibility Compatibility
Compatible with FrSky two way telemetry modules: DFT, DJT, DHT, DHT-U
1.2 1.2 1.2 1.2 Specifications Specifications Specifications Specifications
Dimension: 55*25*14mm
Weight: 12.4g
Operating Voltage Range: 3.5V-10.0V
Operating Current: 100mA
Operating Range: full range (>1.5km)
Servo Frame Rate: 18ms (FS – Normal Speed Mode)
9ms (HS – High Speed Mode)
1.3
1.3 1.3
1.3 Features
Features Features
Features
1) 1) 1) 1) Two Two Two Two external external external external analog analog analog analog telemetry telemetry telemetry telemetry ports ports ports ports (A1&A2) (A1&A2) (A1&A2) (A1&A2) and and and and one one one one digital digital digital digital data-stream data-stream data-stream data-stream port port port port (Rx); (Rx); (Rx); (Rx);
2) 2) 2) 2) RSSI RSSI RSSI RSSI (PWM) (PWM) (PWM) (PWM) and and and and CPPM CPPM CPPM CPPM output output output output ---- If If If If CH3 CH3 CH3 CH3 and and and and CH4 CH4 CH4 CH4 are are are are connected connected connected connected by by by by a a a a jumper, jumper, jumper, jumper, CH1 CH1 CH1 CH1 will will will will output output output output CPPM CPPM CPPM CPPM for for for for CH1~CH8, CH1~CH8, CH1~CH8, CH1~CH8,
and
and
and and CH2
CH2
CH2 CH2 will
will
will will output
output
output output RSSI
RSSI
RSSI RSSI (PWM);
(PWM);
(PWM); (PWM);
3
3 3
3)))) When
When When
When side
side side
side port
port port
port pins
pins pins
pins of
of of
of A1
A1 A1
A1 and
and and
and X
X X
X are
are are
are connected
connected connected
connected by
by by
by the
the the
the jumper,
jumper, jumper,
jumper, A1
A1 A1
A1 will
will will
will change
change change
change from
from from
from external
external external
external analog
analog analog
analog telemetry
telemetry telemetry
telemetry
port
port port
port to
to to
to internal
internal internal
internal built-in
built-in built-in
built-in battery
battery battery
battery voltage
voltage voltage
voltage sensor
sensor sensor
sensor;;;;
4) Firmware upgradeable;
5) Two switchable PPM modes - FS mode and HS mode;
6) Alarm warning on low voltage, poor reception, etc.
2. 2. 2. 2. Set Set Set Set up up up up
2.1 2.1 2.1 2.1 Bind Bind Bind Bind procedure procedure procedure procedure
1) Ascertain that the transmitter is in the PPM mode. Turn off the transmitter.
2) Turn on the transmitter while holding the F/S button on the transmitter module (Ensure that both switches on the
transmitter module are OFF when using D8R-XP in two way mode). Release the button. The RED LED on the transmitter module
will flash, indicating the transmitter is ready to bind to the receiver.
3) Connect battery to the receiver while holding the F/S button on the receiver. The RED LED on the receiver will flash,
indicating the binding process is completed. Turn off both the transmitter and the receiver.
4) Turn on the transmitter and connect the battery to the receiver. The RED LED on the receiver will indicate the receiver is
receiving commands from the transmitter. The receiver/transmitter module binding will not have to be repeated, unless one of the
two is replaced.
Warning: Warning: Warning: Warning: Battery Battery Battery Battery or or or or servos servos servos servos are are are are NOT NOT NOT NOT to to to to be be be be plugged plugged plugged plugged into into into into side side side side ports ports ports ports (A1/A2/Rx), (A1/A2/Rx), (A1/A2/Rx), (A1/A2/Rx), otherwise otherwise otherwise otherwise damage damage damage damage may may may may occur. occur. occur. occur.
2.2
2.2 2.2
2.2 Range
Range Range
Range check
check check
check
A pre-flight range check should be done before each flying session. Reflections from nearby metal fences, concrete
buildings or trees can cause loss of signal both during range check and during the flight.
The following steps are to be followed to perform the range check of the model before the flight:
1)
Place the model at least 60cm (two feet) above non-metal contaminated ground (e.g. on a wooden bench).
2) The receiver antennas should be separated in the model, and do not touch the ground.
3) Place the antenna of the transmitter in a vertical position.
4) Turn on the transmitter and the receiver, press the F/S button of the transmitter module for 4 seconds to enter range
check mode, the RED LED of the transmitter module will be off, GREEN LED will flash rapidly, and the beeper will sound. The
effective distance will be decreased to 1/30 of full range.
5) Walk away from the model while simultaneously operating the controls on the transmitter, confirming that all controls
operate normally to a distance of at least 30 meters (~30 yds).
6) Press the F/S button of the transmitter module for 1S-4S to exit range check mode, RED LED will be back on, indicating
normal operation is back.
2.3
2.3
2.3 2.3 Setting
Setting
Setting Setting failsafe
failsafe
failsafe failsafe
Failsafe is a useful feature in which all controls move to a preset position whenever the control signal is lost for a period of
time. D8R-XP supports failsafe function for all channels.
Follow the steps below to set failsafe positions for each channel:
1)
Bind the receiver first and turn on both the transmitter and the receiver;
2) Move the controls to the desired failsafe position for all channels;
3) Press briefly the F/S button on the receiver (less than 1 second). The transmitter module will make a long “beep” ,