Introduction
Thank you for purchasing FrSky RX4R 4/24CH telemetry receiver. The RX4R features 4 PWM outputs with
extremely high precision and low latency. The latency of PWM output is 9ms less than that of X series receivers in
high speed mode. RX4R features redundancy function as well, so another receiver can be added as a back-up in
case the first one fails. Last but not least, the RX4R and the whole RX-line has a 40% increase in range compared
to the previous X series receivers. In order to fully enjoy the benefits of this system, please read the instruction
manual carefully and set up the device as described below.
What’s New
● CH1~CH4 outputs high precision PWM signal (Precision: less than 0.5μs)
●
Under the same conditions, the effective communication distance of RX6R is about 1.4 times than that of X series
receivers.
●
Installed with ACCESS protocol
Range Check
A pre-flight range check should be done before each flying session. Reflections from nearby metal fences, concrete
buildings or trees can cause loss of signal both during range check and during the flight. Under Range Check Mode,
the RF power would be decreased and Range distance to 1/30 --1/10 that of Normal Model, about 30 meters.
1. Place the model at least 60cm (two feet) above non-metal contaminated ground (e.g. on a wooden bench). The
receiver antenna should be in vertical position.
2. For Taranis X-Lite Pro as an example, turn on the transmitter and power on the receiver, go to: MODEL
SETUP/Internal RF/Range.
3. For transmitter RF module, please refer to its manual.
Much more operation and instruction please refer to radio manual.
Smart Port (S. Port) is a signal wire full duplex digital transmission interface developed by FrSky Electronic Co., Ltd. All
products enabled with Smart Port (including XJT module, XSR,X6R and X8R receiver, new hub-less sensors, new Smart Dashboard,
etc), serial port user data and other user input/output devices can be connected without limitations for numbers or sequences at a high
transmission speed.
Specifications
● Dimension: 18*17*7mm (L × W × H)
● Weight: 2.0g / 2.4g (with two antennas)
●
Number of Channels: 24CH
●
Operating Voltage Range: 3.5V~10V
●
Operating Current: 100mA@5V
●
Operating Range: >2km
●
Compatibility: ACCESS/*ACCST firmware
* Need to upgrade to the corresponding ACCST firmware
● Servo frame rate: 7ms (HS-- High Speed Mode) / 18ms (FS--Normal Speed Mode)
Feature
● Small and High sensitivity (40% increase of the range compared to previous X series receivers)
●
Higher precision PWM
●
Low latency PWM output
●
Lower power consumption
●
Redundancy function supported
●
Smart Port enabled and telemetry data transmission supported
●
Battery voltage detection supported
●
2 detachable IPEX 4 connector antennas
●
PCB protection with the comformal coating craftwork
How to Switch FS mode/HS mode
a)
The factory default setting is FS mode.
b)
To go to the receiver [Options], select the 7ms PWM or not.
Note: The SBUS output is 7ms, no matter HS/FS mode.
Note:
1. X meanings neglect.
2. The default output of RX4R is standard SBUS signal (1-16CH). Hold F/S button for about 5
seconds, CH16 will output RSSI. Repeat the steps above, the value of Channel 16 will output CH16.
LED state
Blue LED
Off
Off
X
X
On
Off
X
Green
LED
On
Flash
Flash
On
On
On
Off
Red
LED
On
Flash
Off
Off
Off
Off
Flash
Status
Register
Register successfully
Bind
Binding successfully
Working under HS Mode
Working under FS Mode
Failsafe
Registration & Automatic binding (Smart Match )
With the FrSky ACCESS protocol, the transmitter/transmitter module can bind receiver without using the "F/S"
button.
Follow the step below to finish the Registration & binding procedure:
1. Put the transmitter/transmitter module into [Reg] status.
1.1 For Taranis X-Lite Pro as an example, turn on the transmitter, go to the MENU-MODEL SETUP-PAGE 2,
choose Internal or External RF, and select [Reg].
2. Connect the battery to the receiver while holding the F/S button on the receiver. The RED LED and GREEN LED
on the receiver will be on, indicating into the [Reg] status. Select [ENTER] on the transmitter, The RED LED and
GREEN LED will flash, and the transmitter displays [Registration ok].
3. Turn off the receiver.
4. Move the cursor to select the receiver 1 [Bind].
5. Connect the battery to the receiver, the GREEN LED will flash, indicating into the [Bind] status. Select the RX,
the GREEN will keep lit, and the transmitter displays [Bind successful].
6. The transmitter exit [Bind], GREEN LED will keep lit, RED LED will be off, indicating Working normally
.
TM
Overview
18
17
Inverted
S.Port signal
BOT
F/S
4 / 24 C H
FrSky Electronic Co., Ltd. www.frsky-rc.com Contact us: [email protected]
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
01140137
Version
1.0
Instruction Manual for FrSky ACCESS RX4R
FrSky Electronic Co., Ltd. www.frsky-rc.com Contact us: [email protected]
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
01140137
Version
1.0
Instruction Manual for FrSky ACCESS RX4R
