Front Runner Toyota LAND Cruiser 100 SLIMLINE II Скачать руководство пользователя страница 1

1

Toyota LAND Cruiser 100

SLIMLINE II RACK

(

1345MM X 1964mm

)

FATL002 / KRTL029T

INSTALL TIME:  1 Hour

FATL002 / KRTL029T_REV_A02

IMPORTANT WARNING!

IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR
VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY IN-
JURY OR DEATH TO YOU OR TO OTHERS. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER
PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PROD-
UCTS FOR ADJUSTMENT, WEAR, AND DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS
AND CAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU DO NOT UNDER-
STAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOR-
OUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSION-
AL INSTALLER OR OTHER QUALIFIED PERSONNEL.

READ ME FIRST: 

Thank you for purchasing a Front Runner Slimline II Rack.

This Roof Rack consists of a kit that contains:
1.) A Slimline II Tray
2.) A mounting system specific to your vehicle

This document will help you fit the Slimeline II Tray to your specific vehicle.

Содержание Toyota LAND Cruiser 100 SLIMLINE II






Отзывы: