Fronius TransSteel 2700c Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 120

background image

Troubleshooting

General

The devices are equipped with an intelligent safety system. This means that to a large
extent it has been possible to dispense with melting-type fuses. Melting-type fuses there-
fore no longer need to be replaced. After a possible malfunction has been remedied, the
device is ready for use again.

Safety

WARNING!

Work that is carried out incorrectly may result in serious injury or damage to prop-
erty.

▶

The activities described below must only be carried out by trained and qualified per-
sonnel.

▶

Observe the safety rules in the power source Operating Instructions.

WARNING!

An electric shock can be fatal.

Before opening the unit

▶

Turn the mains switch to the "O" position

▶

Unplug the device from the mains

▶

Put up an easy-to-understand warning sign to stop anybody inadvertently switching
it back on again

▶

Using a suitable measuring device, check to make sure that electrically charged
components (e.g. capacitors) have discharged

WARNING!

Danger from inadequate ground conductor connection.

Possible serious injury and damage to property.

▶

The housing screws provide a suitable ground conductor connection for earthing the
housing and must NOT be replaced by any other screws that do not provide a reli-
able ground conductor connection.

Fault diagnosis

Make a note of the serial number and configuration of the device and contact our After-
Sales Service team with a detailed description of the error, if
-

errors occur that are not listed below

-

the troubleshooting measures listed are unsuccessful

95

EN

«
...
93
94
95
96
97
...
»

Содержание TransSteel 2700c

























































































































Отзывы:

Нет отзывов

Похожие инструкции для TransSteel 2700c

Бренд: NANO Страницы: 28

Бренд: LENCO Страницы: 1

Бренд: Xoro Страницы: 122

Бренд: STEELE PRODUCTS Страницы: 56

Бренд: Virgin Страницы: 2

Бренд: ELCOS Страницы: 36

Kardon ESQUIRE 2

Бренд: Harman Страницы: 12

DCA-300SSK III Series

Бренд: MQ Power Страницы: 104

Бренд: KUMATSUGEN Страницы: 32

Бренд: KUMATSUGEN Страницы: 68

Бренд: Audiovox Страницы: 29

D7000XP - DVD Player - 7

Бренд: Audiovox Страницы: 33

Бренд: Audiovox Страницы: 34

Бренд: Audiovox Страницы: 35

D1810 - DVD Player - 8

Бренд: Audiovox Страницы: 32

D1817PK - DVD Player - 8

Бренд: Audiovox Страницы: 37

Бренд: Audiovox Страницы: 31

D1812PK - DVD Player - 8

Бренд: Audiovox Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды