manualshive.com logo in svg

Fronius TransSteel 2200, Руководство по эксплуатации

Поделиться
Скачать
Fronius TransSteel 2200 Скачать руководство пользователя страница 99

When the power source is reset, the majority of the applied settings are deleted.
The following values remain:
-

Welding circuit resistance and welding circuit inductivity

-

Country-specific setting

2nd

Second level of the Setup menu (see "Setup Menu 2nd Level")

Parameters for
MMA Welding

HCU

HotStart current

Unit: %
Setting range: 100 - 200
Factory setting: 150

Hti

Hot current time

Unit: seconds
Setting range: 0 - 2.0
Factory setting: 0.5

Ast

Anti-stick function

Unit: -
Setting range: On, OFF
Factory setting: On

FAC

Reset power source to factory settings

Press and hold one of the "Parameter selection" buttons for two seconds to
restore the factory settings
- when "PrG" appears on the digital display, the power source has been reset.

When the power source is reset, the majority of the applied settings are deleted.
The following values remain:
-

Welding circuit resistance and welding circuit inductivity

-

Country-specific setting

2nd

Second level of the Setup menu (see "Setup Menu 2nd Level")

99

EN-US

Содержание TransSteel 2200









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды