Fronius TransSteel 2200 страница 69 Скачать руководство пользователя

Страница: 69 / 136

MIG/MAG Standard Synergic Welding

MIG/MAG stand-
ard synergic
welding

Press the "Process" button to select SYNERGIC

Press the "Mode" button

to select the desired MIG/MAG mode:

2-step mode

4-step mode

S 4 T = Special 4-step mode

Spot welding/stitch welding

Under certain circumstances, it may not be possible to change welding parameters
that have been set for a system component (remote control, etc.) on the control
panel of the power source.

Press the "Material" button to select the filler metal being used

Press the "Wire diameter" button to select the diameter of the wire electrode being
used

Press the "Shielding gas" button to select the shielding gas being used

Press the "Parameter selection" buttons

to select the welding parameter with which the welding power is to be specified:

Sheet thickness
Welding current
Wire speed
Welding voltage

Set the welding parameters

All parameter set values remain stored until the next time they are changed. This applies
even if the power source is switched off and on again.

Ensure that the ground earth connection has been established

Ensure that the shielding gas supply has been established
-

Power source is ready for welding

EN-US

Содержание TransSteel 2200









































































































































Результаты поиска

Содержание TransSteel 2200

Отзывы:

Похожие инструкции для TransSteel 2200

Бренды по названию

Популярные бренды

Fronius TransSteel 2200, Руководство по эксплуатации

Результаты поиска

Содержание TransSteel 2200

Отзывы:

Похожие инструкции для TransSteel 2200

Бренды по названию

Популярные бренды