Fronius TPS/i Push Скачать руководство пользователя страница 124 | Manualshive

Страница: 124 / 152

background image

Care, maintenance and disposal

General

Under normal operating conditions, the device requires only a minimum of care and
maintenance. However, it is vital to observe some important points to ensure the welding
system remains in a usable condition for many years.

Safety

WARNING!

Danger due to work that has been carried out incorrectly.

This can result in severe personal injury and damage to property.

▶

All the work described below must only be carried out by trained and qualified per-
sonnel.

▶

Fully read and understand this document.

▶

Fully read and understand all the Operating Instructions for the system components,
especially the safety rules.

WARNING!

Danger from electric current.

An electric shock can be fatal.

▶

Turn the power source mains switch to the "O" position.

▶

Disconnect the power source from the mains.

▶

Ensure that the power source remains disconnected from the mains until all work
has been completed.

▶

After opening the device, use a suitable measuring instrument to check that electric-
ally charged components (e.g. capacitors) have been discharged.

CAUTION!

Danger from hot system components.

This can result in severe personal injury and damage to property.

▶

Before starting work, allow all hot system components to cool down to room temper-
ature (+25 °C, +77 °F). For example:

Examples of hot system components include
-

Coolant.

-

Water-cooled system components.

-

Wirefeeder drive motor.

Every start-up

-

Check all hosepacks and the ground earth connection for damage. Replace any
damaged components.

-

Check feed rollers and inner liners for signs of damage. Replace any damaged com-
ponents.

-

Check the wirefeeding hoses for damage. Replace any damaged components.

-

Check contact pressure of feed rollers and adjust if necessary.

-

Check that all screw connections between the robot, wirefeeder holder and wire-
feed unit are secure.

124

«
...
122
123
124
125
126
...
»

Содержание TPS/i Push

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для TPS/i Push

Бренд: Olympia Страницы: 62

BrewZilla 100L - Gen 4

Бренд: KegLand Страницы: 48

Бренд: AmeriWater Страницы: 16

Magnum Alert-900

Бренд: NAPCO Страницы: 76

Бренд: Cobolt Страницы: 5

Бренд: EAW Страницы: 2

Бренд: MPMan Страницы: 32

Бренд: TradeWeld Страницы: 11

Aurora FSBNN3MR-BL

Бренд: Furrion Страницы: 18

Бренд: Northern Industrial Tools Страницы: 18

Hy-Brid Lifts HB-830CE

Бренд: Custom Equipment Страницы: 29

970114-0403 - X 530 5.1-CH PC Multimedia Home Theater Speaker Sys

Бренд: Logitech Страницы: 10

3D TRASAR Series

Бренд: Nalco Страницы: 243

Бренд: EWM Страницы: 60

Бренд: Audiovox Страницы: 8

Бренд: QOLSYS Страницы: 10

SmartStop GLASS

Бренд: Bohle Страницы: 2

Бренд: PowCon Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды