manualshive.com logo in svg

Fronius Calibration system 2.0, Руководство по эксплуатации

Поделиться
Скачать
Fronius Calibration system 2.0 Скачать руководство пользователя страница 45

Connecting the
welding wire cal-
ibration system

NOTE!

The power cables are not relevant for calibration of the welding wire!

Establish data communication between the following:

▶

power source and calibration system (LocalNet, SpeedNet, USB, etc.)

▶

power source and wirefeeder (LocalNet, SpeedNet, USB, etc.)

▶

welding wire calibration system and calibration system

2

1

1

Connect the connection cable to
the welding wire calibration system

IMPORTANT!

 A maximum of 3

connection cables (max. 15 m) can
be used to connect the welding
wire calibration system and the cal-
ibration system!

2

Connect the connection cable to
the calibration system

3

(+) Disconnect power cable from
welding system

4

Connect the welding torch to the
welding system

5

Remove the gas nozzle from the
welding torch

6

Thread the wire
The welding wire should protrude
approx. 200 mm from the contact
tip.

7

7

Thread the welding wire into the in-
take part of the sensor

45

EN

Содержание Calibration system 2.0





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды