Fronius 4,044,008 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 136

background image

9

EN

Safety rules

General

Proper use

The device is manufactured using state-of-the-art technology and according
to recognised safety standards. If used incorrectly or misused, however, it can
cause:
-

injury or death to the operator or a third party,

-

damage to the device and other material assets belonging to the operat-
ing company,

-

inefficient operation of the device.

All persons involved in commissioning, operating, maintaining and servicing
the device must:
-

be suitably qualified,

-

have sufficient knowledge of automated welding, and

-

read and carefully follow these operating instructions as well as the oper-
ating instructions for all system components.

The operating instructions must always be at hand wherever the device is be-
ing used. In addition to the operating instructions, attention must also be paid
to any generally applicable and local regulations regarding accident preven-
tion and environmental protection.
All safety and danger notices on the device
-

must be in a legible state,

-

must not be damaged,

-

must not be removed,

-

must not be covered, pasted or painted over.

For the location of the safety and danger notices on the device, refer to the
section headed "General" in the operating instructions for the device.
Before commissioning the device, rectify any faults that could compromise
safety.

This is for your personal safety!

The device is to be used exclusively for its intended purpose.

Any use above and beyond this purpose is deemed improper. The manufac-
turer shall not be held liable for any damage arising from such usage.
Proper use includes:
-

carefully reading and following all the instructions given in the operating
instructions

-

studying and obeying all safety and danger notices carefully

-

performing all stipulated inspection and servicing work.

The device is designed for use in industry and the workshop. The manufactur-
er accepts no responsibility for any damage caused through use in a domestic
setting.
The manufacturer likewise accepts no liability for unexpected or incorrect re-
sults.

«
...
7
8
9
10
11
...
»

Содержание 4,044,008









































































































































Отзывы:

Нет отзывов

Похожие инструкции для 4,044,008

Бренд: A&D Страницы: 35

and Vantage Pro

Бренд: DAVIS Страницы: 4

and Vantage Pro

Бренд: Davis Instruments Страницы: 4

Бренд: Datavideo Страницы: 45

Бренд: RaceChip Страницы: 12

Бренд: Kathrein Страницы: 7

Бренд: Kathrein Страницы: 2

Бренд: LAS Страницы: 44

Бренд: LAS Страницы: 24

Бренд: Waterpik Страницы: 2

Бренд: Abicor Binzel Страницы: 44

Бренд: Omron Страницы: 25

Бренд: Gamko Страницы: 28

Бренд: Echomaster Страницы: 8

Бренд: TREND Страницы: 19

ANOMULTI ROUND WITH CABLE CLIP AND CABLE AND SAUCER

Бренд: ROSE DISPLAYS Страницы: 4

Multi Slider Swift

Бренд: Waterbird Страницы: 15

Бренд: V2 Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды