Fronius 4,044,008 Скачать руководство пользователя страница 75

Страница: 75 / 136

Start-up

Prerequisites for
start-up

The following prerequisites must be fulfilled for the start-up:
-

Torch body changeover station bolted to the underlying surface

Torch body changeover station installed

All torch body sensors checked, wire sensor set

All torch bodies have been prepared

When using a Robacta hosepack: system components for Robacta hosepack pre-
pared

When using a Robacta Drive or Robacta Drive CMT hosepack: torch body coupling
has been prepared

Power source has been prepared

Torch body coupling mounted onto robot

Torch bodies aligned for special rack positions (only if necessary)

Compressed-air booster unit connected and adjusted

Torch body changed manually

Robot set up using robot programming aid

Start-up

The torch body changeover station is started up by an active signal from the robot control.

Содержание 4,044,008









































































































































Результаты поиска

Содержание 4,044,008

Отзывы:

Похожие инструкции для 4,044,008

Бренды по названию

Популярные бренды

Fronius 4,044,008, Руководство по эксплуатации

Результаты поиска

Содержание 4,044,008

Отзывы:

Похожие инструкции для 4,044,008

Бренды по названию

Популярные бренды