manualshive.com logo in svg

Fröling PE1 Pellet 10, Руководство по эксплуатации

Поделиться
Скачать
Fröling PE1 Pellet 10 Скачать руководство пользователя страница 62

5.6.3 Cleaning the Lambda probe

❒ Remove the cover plate on the boiler flow
❒ Press the thermal insulation behind it slightly downwards

 

❒ Carefully remove the Lambda probe (1) and plastic bushing (2 – if installed)

➥ Pay attention to the cables of the Lambda probe!

❒ Carefully remove impurities from the measuring ports with a fine brush and ash

vacuum

➥ Hold the Lambda probe with the tip downwards so that deposits can fall out of

the measuring ports

❒ Check the plastic bushing (2) for dirt and cracks, replace if necessary

➥ IMPORTANT: The seal surface of the plastic bushing must lie flat after

assembly

CAUTION:

▪ Do not clean the Lambda probe with compressed air
▪ Do not use chemical cleaning agents (brake cleaner, etc.)
▪ Careful handling of the Lambda probe, no “tapping” or cleaning with a wire brush

 

 

 

5

Servicing the system

Maintenance work by technicians

62

Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froeling.com

Содержание PE1 Pellet 10





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды