Fritz! Box 6490 cable Скачать руководство пользователя страница 152

Страница: 152 / 173

FRITZ!Box 6490 Cable

152

Switching the Wireless Network On and Off

Pick up the handset.

Wait for the second-long positive acknowledgment tone.

Hang up the handset.

Disabling: Call Diversion for FON 2

Press the keys

s402rss

on the telephone.

Pick up the handset.

Wait for the second-long positive acknowledgment tone.

Hang up the handset.

24.4

Switching the Wireless Network On and Off

Press the following keys on the telephone:

Pick up the handset and hang it up again.

24.5

Loading Factory Settings

Press the keys

r991s15901590s

Pick up the handset and hang it up again.

The factory settings are loaded. Then the FRITZ!Box will re-
start.

delayed (after 20 seconds)

r422s

<destination num-

ber>

only when busy

r432s

<destination num-

ber>

immediately when busy, oth-
erwise delayed

r442s

<destination num-

ber>

Type of Call Diversion

Keys

Function

Keys

Wireless LAN on

r96s1s

Wireless LAN off

r96s0s

All settings you made in the FRITZ!Box will be deleted.

Содержание Box 6490 cable














































































































































































Результаты поиска

Содержание Box 6490 cable

Отзывы:

Похожие инструкции для Box 6490 cable

Бренды по названию

Популярные бренды

Fritz! Box 6490 cable, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Box 6490 cable

Отзывы:

Похожие инструкции для Box 6490 cable

Бренды по названию

Популярные бренды