Fritz! Box 6490 cable Скачать руководство пользователя страница 149

Страница: 149 / 173

Call Diversion

FRITZ!Box 6490 Cable

149

24.3

Call Diversion

Call diversion automatically diverts incoming calls to a previ-
ously specified external telephone number.

If your telephony provider supports this, calls will be diverted
by your provider. Otherwise the FRITZ!Box establishes a sec-
ond connection. In either case, extra charges will accrue ac-
cording to your contracted telephone rates.

Enabling: Call Diversion for All Calls

Here is how to configure call diversion to an external number
(destination number) that applies to all incoming calls:

Press the following keys on the telephone:

Pick up the handset.

Wait for the second-long positive acknowledgment tone.

Hang up the handset.

Disabling: Call Diversion for All Calls

Press the following keys on the telephone:

Pick up the handset.

Wait for the second-long positive acknowledgment tone.

Hang up the handset.

Type of Call Diversion

Keys

immediately

s21s

<destination num-

ber>

delayed (after 20 seconds)

s61s

<destination num-

ber>

only when busy

s67s

<destination num-

ber>

Type of Call Diversion

Keys

immediately

s21ssr

delayed (after 20 seconds)

s61ssr

only when busy

s67ssr

Содержание Box 6490 cable














































































































































































Результаты поиска

Содержание Box 6490 cable

Отзывы:

Похожие инструкции для Box 6490 cable

Бренды по названию

Популярные бренды

Fritz! Box 6490 cable, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Box 6490 cable

Отзывы:

Похожие инструкции для Box 6490 cable

Бренды по названию

Популярные бренды