Fritsch PULVERISETTE 5 Скачать руководство пользователя страница 31

Страница: 31 / 72

6.1.2 Number of balls per grinding bowl (independent of the material quantity)

A higher number of balls will reduce the grinding time and the grinding

result will have a smaller particle size distribution.

Ball diameter (mm) Grinding bowl

volume (ml)

250

500

Number of balls (pcs)

250 - 300

1200 - 1300

2000 - 2500

Number of balls (pcs)

25 -30

50 - 150

100 - 250

Number of balls (pcs)

45 - 50

70 - 100

Number of balls (pcs)

15 - 20

25 - 35

Number of balls (pcs)

5 - 6

Number of balls (pcs)

These are reference figures: The number of balls may need to be deter-

mined through experimentation.

CAUTION!
When grinding with a ball size of

30 mm or

40 mm,

do not let the device run unsupervised. The vibrations

may lead to shifting.

Using the device

- 31 -

Содержание PULVERISETTE 5









































































Результаты поиска

Содержание PULVERISETTE 5

Отзывы:

Бренды по названию

Популярные бренды

Fritsch PULVERISETTE 5, Руководство по эксплуатации

Результаты поиска

Содержание PULVERISETTE 5

Отзывы:

Бренды по названию

Популярные бренды