manualshive.com logo in svg

Fritsch ANALYSETTE 3, Руководство по эксплуатации

Поделиться
Скачать
Fritsch ANALYSETTE 3 Скачать руководство пользователя страница 21

4 

Installation

4.1  Transport

The device is delivered in a cardboard box. In the case of delivery with

several accessories, the device is delivered in a transport crate.

WARNING!
Improper lifting can lead to personal injury or property

damage. The machine must only be lifted with suitable

equipment by qualified personnel.

The guarantee excludes all claims for damage due to improper transport.

4.2  Unpacking

n

In the case of delivery in a crate, pull out the nails that fasten the lid

to the surrounding packaging.

n

Remove the lid.

n

Take out the accessories.

n

To remove the device, three hexagon screws under the wooden plate

must be unscrewed.

n

Compare the contents of the delivery with your order.

Keep the wooden plate, screws and washers, as this

transport securing device must be reattached in the

case of further transport or return.

4.3  Setting up

n

Place the device on a flat, stable surface. It does not have to be fas-

tened to the surface. Leave sufficient space beside the device for

placing the accessories used.

n

The space behind the device must be freely accessible so that the

main switch on the mains connection can be accessed quickly in case

of emergency.

n

The device rests on three flat coil spring assemblies. Level the sieve

shaker:
– ANALYSETTE 3:

Level the sieve shaker by screwing these feet in or out so that

during sieving, the sieving stock is evenly distributed across the

entire sieve surface.

 

Installation

 

 

- 19 -

 

Содержание ANALYSETTE 3



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды