Fritsch ANALYSETTE 3 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 58

background image

NOTICE!
– The toothed belts must only be released or

clamped in the switched off state.

– Before switching on again, ensure that the two

toothed belts are evenly, tightly clamped using the

knurled knobs.

2.7 Hazardous points

n

Crushing hazard at the sieve tensioning system

n

Crushing hazard between vibratory plate and housing

2.8 Electrical safety

2.8.1 General information

The main switch separates the device from the mains on two poles.

2.8.2 Protection against restart

After switching off at the main switch and switching on again, the START

key must be pressed for start-up.

2.8.3 Overload protection

The mains fuse provides overload protection.

Safety information and use

- 16 -

«
...
16
17
18
19
20
...
»

Содержание ANALYSETTE 3



























































Отзывы:

Нет отзывов

Похожие инструкции для ANALYSETTE 3

Бренд: Obdstar Страницы: 10

Бренд: HAMAR LASER Страницы: 49

Бренд: idiag Страницы: 10

Versaflo S Series

Бренд: 3M Страницы: 11

DBI Sala EXOFIT

Бренд: 3M Страницы: 32

Бренд: 3M Страницы: 8

Бренд: Accurate Bio-Medical Technology Страницы: 35

Бренд: Eaton Страницы: 16

Бренд: Eaton Страницы: 15

Бренд: unios Страницы: 2

Бренд: RAMVAC Страницы: 53

Бренд: Sabo Страницы: 76

2261998USBA1-XX

Бренд: MMF POS Страницы: 5

Бренд: Garmin Страницы: 41

Бренд: Opvimus Страницы: 50

Бренд: Irwin Страницы: 2

Бренд: Mindray Страницы: 295

Бренд: ZAMST Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды