manualshive.com logo in svg

Fristam Pumps FP, Оригинальные инструкции, инструкции по сборке, Страница: 7 / 40

Поделиться
Скачать
Fristam Pumps FP Скачать руководство пользователя страница 7

7

Noise Generated by Running Pump

Hearing damage.

►

Wear ear protectors when using pumps with specified sound 
pressure levels of greater than 80 dBA.

2.6

Disposal

2.6.1

Disposal of Transportation Package

►

Recycle the transportation package.

2.6.2

Models KF and L 1: Disposal of Grease

►

Dispose of grease and objects saturated with grease in an 
environmentally friendly manner in accordance with appli-
cable regulations.

2.6.3

Models L 2, L 3/L3V, L 4V: Disposal of Lubricating Oil 

►

Dispose of oil and objects saturated with oil in an 
environmentally friendly manner in accordance with 
applicable regulations.

2.6.4

Disposal of Pump

1. Carefully clean the pump. Dispose of residues in an 

environmentally friendly manner in accordance with 
applicable regulations.

2. Dismantle the pump into its constituent parts.

3. Dispose of the pump parts in an environmentally friendly 

manner in accordance with applicable regulations.

2.6.5

Disposal of Electrical and Electronic Scrap

►

Dispose of electrical and electronic scrap in accordance with 
applicable directives.

3

Design and Function

3.1

Principles of Design

Fig. 5

Principles of design of pumps illustrated using the FPE model

3.1.1

Pump Head (A)

Fig. 6

Pump  head

Shaft Seal (12)

Two seal types are available for use:

– Single shaft seal

– Double shaft seal

With the double shaft seal, there are two additional connec-
tions for the sealing liquid on the pump casing. These con-
nections are not shown in the following figures.

A

Pump head

B

Lantern

C

Electric motor

11

Discharge line connection

12

Shaft seal

13

Impeller

14

Pump cover

15

Suction line connection

16

Pump casing

B

C

A

11

12

13

14

15

16

Содержание FP









































Отзывы:

Нет отзывов