manualshive.com logo in svg

Fristam Pumps FP, Оригинальные инструкции, инструкции по сборке, Страница: 20 / 40

Поделиться
Скачать
Fristam Pumps FP Скачать руководство пользователя страница 20

/ / FP PUMP SERIES / / /

20

4. Adjust the clearance to the values specified in 

Table 6  , 

"Standard Clearence," page 20

, 

Table 7  , "Clearances in model 

S," page 20

 or 

Table 8  , "Clearances in model R," page 20

 re-

spectively. 

Clearance too large

►

If the clearance between the housing and the impeller is too 
large, rework the stationary bushing. 

Grinding stationary bushing to size

1. Remove the stationary bushing from the shaft sealing kit. 

The location of the stationary bushing is indicated in the 
"

Sectional drawing of shaft seal

" in the appendix of the "

Order 

documents

". 

2. Grind the stationary bushing to the required size. 

3. Re-install the stationary bushing. 

4. Slide the key and the impeller onto the shaft and tighten 

them with the impeller nut. 

5. Measure the clearance again.

►

If the code "S" or "R" (additional letter 1) is printed on the 
rating plate, adjust the clearance to the values specified in 

Table 7  , "Clearances in model S," page 20

 or 

Table 8  , 

"Clearances in model R," page 20

 respectively. (Position of 

additional letter 1: See 

Chapter 3.3, "Pump Key," page 9

)

9.10 Pump Head Attachment

The pump assembly is dependent on the respective pump size 
and model as well as the respective shaft seal (see 

“Order-

Related Documents“)

 in the attached documents. 

Incorrect Elastomers

Pump leakiness.

►

Ensure that the elastomers are appropriate for the condition 
of the pumping medium. Please refer to the 

“Order-Related 

Documents“

.

Preparation

►

Clean all pump parts and check for damage and accuracy of 
fit.

►

If necessary, rework or replace pump parts. 

►

Assemble in clean conditions, carefully, and using little force. 
The seals could be permanently deformed or break in part.

►

Replace all O-rings.

►

To reduce friction, wet the O-rings and the sliding faces with 
water, alcohol, or silicone grease. 

►

Clean the sealing surfaces of the mechanical seals with a 
degreaser, e.g., OKS 2610 Universal Cleaner. Do not allow the 
sealing surfaces to come into contact with oil or grease and 
do not touch with your fingers afterwards. 

Tip: The joint retaining compound "Euro Lock A64.80," e.g., is suit-
able for gluing in bearings and bushings.

Tip: The screw retaining compound "Euro Lock A24.10," e.g., is suit-
able for gluing in set screws.

Pump Size

Clearances in mm

Impeller–Pump Cover

Impeller–Casing

711/712

0.5

0.5

721/722

0.5

0.7

741/742

0.5

0.5

751/752

1.0

1.0

3401/3402

0.5

0.5

3521/3522

0.5

0.5

3531/3532

0.5

1.5

3541/3542

1.0

1.0

3451/3452

1.0

1.0

3551/3552

1.0

1.0

1151/1152

2.0

2.0

1231/1232

-

1.5

1241/1242

-

1,0

1251/1252

-

1.5

Table 6   

Standard Clearence

Pump Size

Clearance FPS in mm

Impeller / pump cover

Impeller / casing

(calculated)

711/712

0,5

(5,5)

721/722

0,5

(5,5)

741/742

0,5

(5,5)

751/752

1.0

(5,0)

Table 7  Clearances in model S

3521/3522

0,5

(10,5)

3531/3532

0,5

(11)

3541/3542

1,0

(11)

3551/3552

1,0

(11)

Pump Size

Clearance FPR in mm

Impeller / pump cover

(calculated)

Impeller / casing

3521/3522

(10,5)

0,5

3531/3532

(11)

0,5

3541/3542

(11)

1,0

3551/3552

(11)

1,0

Table 8  Clearances in model R

Pump Size

Clearance FPS in mm

Impeller / pump cover

Impeller / casing

(calculated)

Table 7  Clearances in model S

Содержание FP









































Отзывы:

Нет отзывов