manualshive.com logo in svg

Fristam Pumps FP, Оригинальные инструкции, инструкции по сборке, Страница: 10 / 40

Поделиться
Скачать
Fristam Pumps FP Скачать руководство пользователя страница 10

/ / FP PUMP SERIES / / /

10

4.1.2

Moving With Industrial Trucks

Preparation

►

Ensure that the pump is adequately secured to the pallet. 

Procedure 

1. Pick up the pallet with the forks on the industrial truck. 

2. Carefully move the pallet to the designated location and set 

down. 

Fig. 13

Moving with industrial truck

4.1.3

Moving With Crane

Falling Parts

Death from crushing, pinching of extremities, material damage.

►

Do not lift the pump at the eyebolts on the motor and pump 
casing to move because these eyebolts are not designed for 
the total weight. 

►

Only use hoists that are designed for the total weight of the 
pump.

►

Ensure that the area below the pump is clear of people.

Swinging Parts

Crushing and serious injuries. 

►

Start and stop the crane with pump smoothly. 

►

Ensure that the danger zone of the pump is clear of people. 

Auxiliary Equipment

Hoists: round slings tested in accordance with DIN EN 1492-1 
and 1492-2 

Preparation

►

Remove load-securing devices. 

Procedure

1. Wrap the round sling twice around the back end of the 

motor. Do not lay over the fan shroud (see 

Fig. 14 Moving 

with crane

).

2. Lay the other end of the round sling between the lantern 

and the pump casing. Do not lay the round sling over any 
sharp edges or corners. 

3. Guide both loops to the crane hook and rotate by 180° to en-

sure that the belt will not slip on the hook. 

4. For double shaft seal: 

Note:

 Round sling compresses sealing water tubes. Material 

damage to double shaft seal.

►

Do not lay the round sling on the sealing water tubes.

5. Position the center of gravity to ensure that the pump is lift-

ed horizontally. 

6. Lift the pump. 

.

Fig. 14

Moving with crane

5

Storage

5.1

Safety Instructions

►

Corrosion: Condensation can build up under a tarp and 
destroy the pump.

– Ensure adequate ventilation.

5.2

Storage Conditions

►

Store the pump as follows:

– Dry, in low humidity

– Protected against frost and heat, optimally at a tempera-

ture of 20°C to 25°C 

– Ventilated

– Dust-free

Содержание FP









































Отзывы:

Нет отзывов