Fristam Pumps FKL 15 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 40

Fristam Pumps FKL 15 Скачать руководство пользователя страница 33

33

11.5 EC Declaration of Conformity

The manufacturer: FRISTAM Pumpen KG (GmbH&Co.)



Kurt-A.-Körber-Chaussee 55



21033 Hamburg, Germany

declares that the following product (pump with motor):

– centrifugal pump types FP, FPE, FP…V, FPH, FPEH,

FPH…V, FSPE, FSP…V, FM, FZ, FC, CF, CFE, FPM and FSM

– Positive displacement pump types: FK, FKL, FL, FL2, and

FL3

– Powder mixer type: PM

– (for serial number, see cover page of operating manual)

conforms to all relevant requirements of the

EU Machinery Di-

rective (2006/42/EC)

.

The machine also conforms to the relevant requirements laid
down in the

Low Voltage Directive (2014/35/EU)

and the

EMC

Directive (2014/30/EU)

No. 1935/2004 and FDA.

The above product conforms to the following standards:

– DIN EN 809:2012-10: Pumps and pump units for liquids -

Common safety requirements

– DIN EN ISO 12100:2011-03: "Safety of machinery - General

principles for design, risk assessment and risk reduction")

Documentation officer: Julia Friedsch



Telephone: +49(0)40 72556-107



Address: see manufacturer address

Hamburg, 30 October 2020

Julia Friedsch / Head of Quality Management

11.6 EG Declaration of Incorporation

The manufacturer: FRISTAM Pumpen KG (GmbH&Co.)



Kurt-A.-Körber-Chaussee 55



21033 Hamburg, Germany

declares that the following product (pump without motor):

– centrifugal pump types FP, FPE, FP...V, FPH, FPEH, FPH...V,

FSPE, FSP...V, FM, FZ, FC, CF, and CFE

– Positive displacement pump types: FK, FKL, FL, FL2, and

FL3

– Powder mixer type: PM

– (for serial number, see cover page of operating manual)

is an incomplete machine in accordance with the

Machinery Di-

rective (2006/42/EC) Annex II B

.

The relevant, basic safety and health requirements of Annex I of
the above-mentioned Directive have been applied and adhered
to.

The incomplete machine further meets all the provisions of the
Directive (EC) No. 1935/2004 and FDA.

The incomplete machine may only be put into operation when
it has been determined that the machine into which the incom-
plete machine is to be installed complies with the Machinery Di-
rective (2006/42/EC).

The above product conforms to the following standards:

– DIN EN 809:2012-10: Pumps and pump units for liquids -

Common safety requirements

– DIN EN ISO 12100:2011-03: "Safety of machinery - General

principles for design, risk assessment and risk reduction"

The manufacturer undertakes to transmit the special documen-
tation on the partly completed machinery electronically to the
national authorities when requested to do so.

The technical documentation belonging to the machine as per
Annex VII Part B have been prepared.

Documentation officer: Julia Friedsch



Telephone: +49(0)40 72556-107



Address: see manufacturer address

Hamburg, 30 October 2020

Julia Friedsch / Head of Quality Management

«
...
31
32
33
34
35
...
»

Содержание FKL 15









































Отзывы:

Нет отзывов