TO BE REMOVED BY THE CUSTOMER AFTER INSTALLATION IS COMPLETE
INSTALLATION CHECKOFF LIST
Doors
Handles are secure and tight
Door seals completely to cabinet on all sides
Freezer door is level across the top
Leveling
Refrigerator is level, side to side and tilted 1/4” (6mm) front to back
Toe grille is properly attached to refrigerator
Cabinet is setting solid on all corners
Electrical Power
House power turned on
Refrigerator plugged in
Ice Maker
House water supply connected to refrigerator
No water leaks present at all connections - recheck in 24 hours
Ice Maker is turned ON.
Final Checks
Shipping material removed
Fresh Food and Freezer controls set
Crisper Humidity controls set
Registration Card sent in
Refer to your
Owner’s Use and Care Manual for
additional information about your refrigerator.
• Load refrigerator from side of cabinet only.
• Do not run retaining straps over handles.
• Do not over-tighten retaining straps.
• Never use refrigerator handles to move the
refrigerator.
• Remove tape from doors only after unit is in
place.
HAND TRUCKING
1
Remove Shipping material. (Features may vary per model.)
2
SHIPPING MATERIAL
3
Connect water supply - check for water
leaks.
Turn icemaker OFF if water supply
is not connected immediately.
Connecting to a reverse osmosis system
is not recommended.
WATER SUPPLY
eçìëÉ
éäìãÄáåÖ
äáåÉ
t~íÉêäáåÉ=Üççâìé
WATER SUPPLY
_É=ÅÉêí~áå
íÜÉ=ï~íÉê=î~äîÉ=áë
çéÉå=~åÇ=íÜÉêÉ
~êÉ=åç=äÉ~âëK
qÜÉ=ï~íÉê=î~äîÉ
çå=íÜÉ=Ä~Åâ=çÑ
íÜÉ=êÉÑêáÖÉê~íçê
ïáää=`äáÅâL_ìòò=áÑ
íÜÉ=ï~íÉê=î~äîÉ
áë=ÅäçëÉÇK
4
Allow the following clearances for ease of installation, proper air circulation, and
plumbing and electrical connections:
•
Sides & Top..........3/8”
•
Back.......................1”
INSTALLATION CLEARANCES
NO
NO
NO
NO
NOTE
TE
TE
TE
TE
If you are installing your refrigerator beside a wall, leave 1/2” minimum between
hinges and wall to allow for the door to swing open.
5
All four corners of your refrigerator must rest firmly on a solid floor. Your refrigerator
is equipped with adjustable front rollers or front leveling screws to help level your
unit.
To level cabinet or change door height:
1. Remove toe grille.
2.
Use flat-blade screwdriver or 3/8” socket wrench to adjust front rollers. Use
adjustable wrench to adjust leveling screws.
LEVELING AND ADJUSTING
NO
NO
NO
NO
NOTE
TE
TE
TE
TE
Raise the front of the refrigerator enough so the doors close freely when opened
halfway. The refrigerator should slope ¼” to ½” from front to back. Then level the
refrigerator from side to side.
6
Toe Grille
Adjustable Front Roller
(some models)
Raise
Stationary Front Roller
with Leveling Screw
(some models)
When changing controls, wait 24
hours before making additional
adjustments.
CONTROLS
7
Ensure icemaker
is turned ON.
8
ICEMAKER
DOOR
REMOVAL
(IF NECESSARY)
IF YOU ARE DISSATISFIED WITH THE
INSTALLATION, PLEASE CALL THE STORE
YOU PURCHASED IT FROM.
9
√
See “Normal Operating Sights & Sounds”
in the
Use & Care Manual
so you understand the sounds you may hear once your refrigerator is
running.
√
Please read entire
Use & Care Manual
to become aware of important
safety instructions and to become familiar witrh your new refrigerator.
√
Send in Registration card
to register your refrigerator.
√
Congratulations!
You are ready to enjoy your new refrigerator.
P/N: 240568303
Humidity
Control
Center
Hinge
Shim
Pin
Top Hinge
Cover
Top Hinge
If you need to remove the doors to get your refrigerator
into the house please see “Door Removal and Reversal
Instructions” in your
Use & Care Manual.
Bottom
Water Tube
Cable
Wood
Top Hinge
Cover
Top Hinge
OR
