Specifications
subject to change.
Meets
requirements of
ASSE 1006
USA
•
10200 David Taylor Drive
•
Charlotte, NC 28262
•
1-800-FRIGIDAIRE
•
frigidaire.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
frigidaire.ca
*Height only adjustable to 35
3
/
4
" max. when installed in 35
3
/
4
" max.
standard cabinetry cutout. (Dimensions do NOT include insulation –
insulation blanket may be compressed during installation.)
33
3
/
4
// "
Adjustable
to 35
3
/
4
// "
*
Front
23
3
/
3
4
// "
Left
24
1
/
4
// "
Power supply & water inlet location
(bottom rear)
50
1
/
4
// "
Right
Door in 90
°
open position
27
3
/
4
// "
22
1
/
2
// "
3
1
/
2
// "
min.to
4
1
/
2
// " max.
1"
2
1
/
4
// "
2
1
/
4
// "
**
NOTE:
35
3
/
3
4
// "
max.
height for standard
cabinetry cutout.
(
5
/
5
16
// " min. clearance
required from unit to
underside of countertop.)
3"
18"
24"
min.
Electrical, water,
water
water
and drain lines
must be confined
to shaded area
1
1
/
4
// "
24"
3"
90°
90°
Preferred
drain areas
3"
34"
min. to
35
3
/
3
4
// "
max.
max.
**
FGCD2456Q 05/14
© 2014 Electrolux Home Products, Inc.
Dishwashers
FGCD2456Q FV/VWV/VB
24" Built-In
Dishwasher Specifications
•
Product Shipping Weight (approx.) – 91 Lbs.
•
Voltage Rating – 120V>/>60 Hz>/>15 Amps
(maximum 20 Amps if
connected with disposer)
•
Connected Load (kW Rating) @ 120 Volts = 1.44>kW
(For use on adequately wired 120V, dedicated circuit having 2-wire
service with a separate ground wire. Appliance must be grounded
for safe operation.)
•
Amps @ 120V = 15 Amps
•
Always consult local and national electric & plumbing codes.
Meets requirements of ASSE 1006>—>integral air gap on supply.
•
Water Pressure – Hot water line to dishwasher must provide
between 20 and 90 pounds per square inch (psi) with at least 120°>F
hot water temperature.
•
Make sure location has correct drain, water and electrical outlets
to make connections.
•
Electrical and water supplies should enter cabinet opening on floor,
or through back or side walls, as shown in shaded areas.
•
Keep back free of drain, water & electrical supply.
•
Connections preferably located toward left side of dishwasher.
Do not cross drain, water or electrical lines in front of motor, blower
or frame.
•
If connecting drain hose to sink trap, local code may require
installation of Air Gap Kit
(not included)
.
•
Leveling legs supplied to adjust height.
(Note: Height only adjustable
to 35-3/4" max. when installed in 35-3/4" max. standard cabinetry
cutout. 5/16" min. clearance required from top of unit to underside
of countertop. Dimensions do NOT inlcude insulation — insulation
blanket may be compressed during installation.)
•
When installing adjacent to wall, cabinet or other obstruction that
extends beyond front edge of unit, allow 2" minimum clearance
between opened door and obstruction.
•
Floor should be flat and free of obstructions with carpet removed
to provide motor clearance.
•
When installing at end of cabinet line, sides and back must be
fully enclosed.
•
Do not install unit under a cooktop, damage will occur.
•
Recommended to seal cabinets, enclosing all sides of dishwasher,
including underside of countertop, with oil-based paint or moisture-
proof polyurethane to prevent possible steam/moisture damage.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at frigidaire.com for detailed instructions.