Frigidaire FFHB2740PE страница 23 Скачать руководство пользователя

Страница: 23 / 40

AUTOMATIC ICE MAKER - FREEZER

IMPORTANT

Your ice maker is turned on at the factory

so it can work as soon as you install your

refrigerator. If you cannot connect a water

supply, lift the ice maker’s wire signal arm to

turn it off. Otherwise, the ice maker’s fill valve

may make a loud chattering noise when it

attempts to operate without water.

CAUTION

If the water supply to your refrigerator is

softened, be sure the softener is properly

maintained. Chemicals from a water softener

can damage the ice maker.

CAUTION

NEVER use an ice pick or similar sharp

instrument to break up the ice. This could

damage the ice bin.
To loosen stuck ice, use warm water.

Before replacing the ice bin, make sure it is

completely dry.

Operation & Care of the Freezer

Ice Maker

(select models)

After the refrigerator is installed properly, the ice

maker can produce ice within 24 hours. It can

completely fill the ice bin in about three days.
When using the ice maker for the first time and

in order for the ice maker to work properly, it is

necessary to clear air from water filter tubing.

Once ice maker begins making ice, allow the

bucket to fill completely, then discard the first

TWO FULL buckets of ice. It will take at least

two days to completely fill the bucket on regular

ice making mode or 1½ days on fast ice mode.
The ice maker produces approximately four

2.5 pounds of ice every 24 hours depending on

usage conditions.

Turning the ice maker on and off

Ice production is controlled by lifting/lowering

the ice maker’s wire signal arm. To gain access

to the ice maker, pull the freezer drawer out. Lift

the wire signal arm to turn the ice maker OFF

and lower the wire signal arm to turn it ON.

Ice maker tips

•

If your refrigerator is not connected to a water

supply or the water supply is turned off, turn

off the ice maker by lifting wire signal arm.

Clean the ice maker and ice bin at regular

intervals, especially prior to vacation or moving.
  1  Turn off the ice maker.
  2  Remove the ice bin.
  3  Empty and carefully clean the ice bin

with mild detergent. Do not use harsh or

abrasive cleaners. Rinse with clean water.

4 Allow the ice bin to dry completely before

replacing in the freezer.

5 Replace the ice bin. Turn the ice maker on.
Remove and empty the ice bin if an extended

power failure (one hour or longer) causes

ice cubes in the ice bin to melt and freeze

together.
Remove the ice bin and shake to loosen the

cubes or clean as explained above.

•

The following sounds are normal when the

ice maker is operating:

- Motor running

- Ice dropping into ice bin

- Water valve opening or closing

- Running water

•

Ice cubes stored too long may develop an odd

flavor. Empty the ice bin as explained below.

Quick Ice Function

Your refrigerator is equipped with a Quick Ice

Function, that increases ice production. This

function terminates automatically.

Cleaning the ice maker

Wire

Signal Arm

Содержание FFHB2740PE









































Результаты поиска

Содержание FFHB2740PE

Отзывы:

Похожие инструкции для FFHB2740PE

Бренды по названию

Популярные бренды

Frigidaire FFHB2740PE, Инструкция по использованию и уходу

Результаты поиска

Содержание FFHB2740PE

Отзывы:

Похожие инструкции для FFHB2740PE

Бренды по названию

Популярные бренды