Frigidaire FAHE4044MW0 Скачать руководство пользователя страница 8

Страница: 8 / 72

Shipping Hardware

Foam shipping restraint (inside wash tub)

removed and stored

Shipping bolt (underneath appliance) removed

and stored

Leveling

Washer is level, side-to-side and front-to-back

Cabinet is setting solid on all corners

Water Supply

Use only new hoses and verify rubber sealing

washers are installed

HOT supply is connected to HOT inlet and

COLD supply is connected to COLD inlet

HOT and COLD water supply turned on

No leaks present at water supply connections

or appliance inlet connections -

recheck in 24 hours

Drain

Stand pipe or wall drain height minimum 33”

Drain hose secured in place with cable tie

(shipped in drum)

Electrical Power

House power turned on

Washer plugged in

Final Checks

Installation Instructions and Use and

Care Guide read thoroughly

Water enters drum when cycle starts with lid

lowered.

Registration card sent in

Installation Checklist

NOTE

Hoses are not included with washer purchase. See

“Accessories” section for various inlet hose kits to fi t

your specifi c installation.

SECTION 2 - INSTALLATION INFORMATION

Pre-Installation Requirements

Tools and materials needed for installation:

• Adjustable wrench

• 3/8” (10 mm) box wrench

• Ratchet and socket set

• Adjustable pliears

• Carpenter’s level

• Inlet hoses(x2)

CAUTION

EXCESSIVE WEIGHT HAZARD

To avoid back or other injury, have more than one

person move or lift the appliance.

2 - 2

Содержание FAHE4044MW0









































































Результаты поиска

Содержание FAHE4044MW0

Отзывы:

Frigidaire FAHE4044MW0, Обслуживание, Страница: 8 / 72

Результаты поиска

Содержание FAHE4044MW0

Отзывы: