manualshive.com logo in svg

Frigidaire FAHE4044MW0, Обслуживание, Страница: 43 / 72

Поделиться
Скачать
Frigidaire FAHE4044MW0 Скачать руководство пользователя страница 43

43

SECTION 4 - COMPONENT TEAR DOWN

Wash Plate Cap (Reinstallation)
To reinstall the wash plate cap:

1.  Ensure locking tab is correctly aligned.

2.  Place the wash plate cap onto the wash plate with the 

alignment arrows just offset.

3.  Rotate the wash plate cap clockwise until the locking tab 

clicks into place. The indicating arrows should be aligned.

4 - 13 

aligned

rotate to 

test  lock

not aligned

IMPORTANT

A misaligned locking tab will not securely hold the wash 

plate cap in place and it may come loose during normal use.

IMPORTANT

After reinstalling the wash plate cap, test the locking tab 

by attempting to rotate the cap back counter-clockwise. If 

cap  rotates, locking tab has not been engaged. Rotate cap 

again clockwise with force to engage tab. If tab still has not 

engaged remove cap and inspect locking tab for alignment 

and adjust tab angle as necessary.

locking tab misaligned

locking tab aligned

Содержание FAHE4044MW0









































































Отзывы:

Нет отзывов