manualshive.com logo in svg

Frigidaire FAHE4044MW0, Обслуживание, Страница: 41 / 72

Поделиться
Скачать
Frigidaire FAHE4044MW0 Скачать руководство пользователя страница 41

41

SECTION 4 - COMPONENT TEAR DOWN

Drive motor
The drive motor is held in place on the leg and dome 

assembly with three bolts The motor is isolated with the use 

of a plastic base and plastic collars around the mounting 

bolts. The motor is NOT not grounded.
To remove the drive motor:

1.  Disconnect the washer from electrical source and remove 

the front panel, motor control assembly, drive motor 

shield, and drive belt.

2.  Disconnect each wire terminal from the motor.
3.  Remove all three motor mounting bolts with a 5/16-inch 

socket and ratchet.

4 - 11 

locating pin

xxx terminal

xxx terminal

motor mounting 

bolt (x3)

IMPORTANT

When reinstalling the motor, ensure each of the mounting 

bolts are installed correctly with the ground isolating collars.

IMPORTANT

When reinstalling the motor, ensure the locating pin on the 

motor base has inserted completely into the mounting plate  

before tightening any of the three mounting bolts.

Содержание FAHE4044MW0









































































Отзывы:

Нет отзывов